TOSHIBAINSTRUCTION MANUALDOME CAMERAIK-DP20APlease read this manual thoroughly before use, and keep it handy for future reference.Record in space
When scan limit stops ARE NOT set:The dome camera will move between random stops and random tilt angles until a manual operation from the keyboard is
6.4 CAMERA SETUP6.4.1 FUCUS CONTROL Direct- The focus can be controlled directly using near or far focusing controls.- The focus control has 4 varyi
6.4.2 WHITE BALANCE CONTROL Direct- The White Balance can be set by One Push Trigger operation.MenuMAIN MENUCAMERA MENU-XCAMERA SETUP><FOCUS>
MenuMAIN MENU CAMERA MENU AE MENU- AE (Auto Exposure) mode can be set to FULL AUTO or SHUTTER PRIORITY.- In FULL AUTO mode, the shutter is fixed at 1/
6.4.4 ZOOM CONTROL Direct- The zoom feature has 4 varying speeds.- The IK-DP20A zoom feature can be controlled directly for Wide angle or Telephoto a
The sharpness can be controlled from 0-15, with 15 being the sharpest.To change the SHARPNESS:1. Enter 95 preset to access the main menu.2. Position t
This function masks a user defined area that cannot be viewed by the operator. The mask adjusts with the pan, tilt and zoom of the camera.Privacy Mask
4) It is recommended to set privacy zone bigger than actual masking area.5) During turbo panning or tilting, the privacy zone may shift depending on t
To enable SCAN LIMIT STOPS:1. Enter 95 preset to access the main menu.2. Position the cursor (->) next to PAN/TILT SETUP and press the OPEN button
After a programmed number of minutes of inactivity, the dome camera wiii park to preset 1. The Park Time Minutes can be set from 1 720 minutes. Settin
IMPORTANT SAFEGUARDS1. Road InstructionsAll the safety and operating instructions should be read before the product is operated.2. Retain Instructio
3. Position the cursor next to SCAN SPEED and press the OPEN button to move the cursor to the right.4. Move the joystick up or down to set the speed.5
To set MAX SPEED:1. Enter 95 preset to access the main menu.2. Position the cursor (->) next to PAN/TILT SETUP and press the OPEN button to access
6.7 OTHERS MENU6.7.1 POWER UPDuring Power-Up, the dome camera can be set to start in various modes. PARK: The dome camera will move to Preset 1 posit
MAIN MENU OTHERS MENU<CAMERASETUP>POWER UP PARK<PAN/TILT SETUP> ^FREEZE ACTIVITY ON<PRESET TITLES>LOAD FACTORY DEFAULT^<OTHERS>
the cursor to the right.4. Move the joystick up or down to set freeze activity to ON or OFF.5. To accept the selection, press the OPEN button or to ca
7. Menu Directory :Top menuCAMERA SETUP MENUFOCUS SETUP MENU-24-
7.1 MENU LISTANO SETTINGSTop MenuSub Menul Sub Menu2 ContentsDefaultCameraSetupAuto Exposure ModeFull Auto/Shutter PriorityFull AutoAuto Slow Shutte
8. Preset CommandsThe dome camera can set and perform various preset commands. The following table lists the preset number and whether is can be set
KBD200/300/300V CM6700 modeInput the desired preset number using the numeric keypad.Hold down the PRESET button until the Edit LABEL screen of CM6700
(4) Loosen the lock screw according to ceiling board thickness for attaching to the ceiling.(5) The IK-DP20A is temporarily attached to the topside o
CAUTIONRISK OF ELECTRONIC SHOCK DO NOT OPEN' The CAUTION label, shown on the left, is attached on the camera.CAUTION TO REDUCE THE RISK OF ELECTR
(11) Use a support wire for safety.(12) The hole that fixes a support wire is on the side. [Note: The support wire is not attached.](IK-DP20Adome ba
(JK-H01Adome cover install)(20) To lock the dome cover, insert the support wire and turn to the right with both hands. Fig-7, Fig-810. Switch Setting
(1) SW1 : Camera AddressCameraAddressSW1bill bit2 bitsbit4bit5bitebot7bit81On OffOffOff Off Off Off Off2Off OnOffOff OffOffOff Off3OnOn Off Off Off Of
Camera Address = 1 x bit1 Status + 2 x bit2 Status + 4 x bits Status + 8 x bit4 Status + 16 X bits Status + 32 x bit6 Status + 64 x bit7 Status + 128
S301ONPOWERTERMINALOFFoBNC Connector11. Specifications :OverallTemperature of operation32° to 122°F (0°to 50°C)Preservation temperature-4° to 140°F (
MechanicalPan Range360degrees continuousTilt Range92 degrees (Outdoor)Manual Pan Speeds0.r-907sManual Pan Speeds(turbo)1507sManual Tilt Speeds0.r~457s
LIMITED WARRANTYCCD SECURITY CAMERAThe Imaging Systems Division of Toshiba America infcMmation Systems, Inc. ("ISD") makes the following lim
1. Features and description :IK-DP20A has following function.Quick Install Design - Cuts Installation Time in Half480 Lines Horizontal Resolution300
4. Part names and LocationsTerminal for Control (RS-422)Terminal for Power (24VAC only)BNC connector for Video outInstall brackets (3 legs)RS-422 ter
5. Connections :Basic connection (Direct mode)24V AC UL listed class 2 power supplyKeyboardMake sure to connect to a power supply that allows for at l
6. Operation :(Power On display)TOSHIBA IK-DP20A VERSION *** PROTOCOL TOSHIBA-P ADDRESS 1 COMM 4800/N/8/1When the dome camera powers-up, the software
Manual TILTManual Tilt speed ranges from 0.1 degrees/sec 45 degrees/sec. However, this speed changes when Proportional P/T is ON.Pan Range360degrees c
6.2 PAN/TILT FUNCTIONSWhen scan limit stops ARE NOT set:The dome camera will move in 45-degree increments (cailed stops) horizontally until a manual
Comments to this Manuals