Toshiba VF-nC1 User Manual Page 44
- Page / 143
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
E6581090
D-3
4
4.1.1 How to set a setup parameter
Set the setup parameter according to the logic for control input signals used and the base frequency
of the motor connected. (If you are not sure which setup parameter should be selected among
P, R and P and what values should be specified, consult your reseller.)
Each setup parameter automatically sets all parameters relating to the logic for control input signals
used and the base frequency of the motor connected.
This parameter setting is needed only for the VFNC1 (S)-□□□□P□-W.
Follow these steps to change the setup parameter [Example: Changing from P to P: sink
logic (negative common) and a base frequency of 60Hz]
Key operated LED display Operation
P Turn the power on.
P
Select a parameter among P, R and P, using
the △ and ▽ keys. Select P in this case.
KP KV
Press the ENTER key to confirm your change.
When KP KV is displayed, you can set the setup
parameter.
The operation frequency is displayed (Standby).
The settings of the parameters listed below are changed by the setup parameter.
When you search for I4W parameters, only the parameters in the shaded area will be displayed
as changed parameters.
■Values set by each setup parameter
Parameters set P
(Mainly in Asia)
R
(Mainly in Europe)
P
(Mainly in North America)
H
0 [Sink logic (negative common)] 100 (Source logic (positive common)) 0 [Sink logic (negative common)]
H / H
220 (V) 220 (V) 230 (V)
H
1410 (min
-1
) 1410 (min
-1
) 1710 (min
-1
)
HJ, WN, H
50.0 (Hz) 50.0 (Hz) 60.0 (Hz)
XN / H
50.0 (Hz) 50.0 (Hz) 60.0 (Hz)
Setup parameter
After you set the basic parameter V[R to (Initialize to default setting) or the first power, the
inverter will be in setup parameter mode. When the inverter is in this mode, you need to set a
setup parameter, as de scribed below, to make the inverter ready for operation.
▲
▼
ENT
★Yo u can change this parameter setting. To do so, you need to reset the basic parameter V[R
to (default setting).
★Yo u c a n a l so c h a n ge the parameters in the table below individually even after setting a setup
parameter.
- Industrial Inverter 1
- I. Safety precautions 2
- Danger 4
- Warning 4
- Danger 4
- Warnin 5
- (inverter) 6
- Maintenance and inspection 6
- Disposal 6
- Attach warning labels 7
- ― Contents ― 8
- 1. Read first 10
- [Front panel] 12
- ■Self-up terminal block 13
- VFNC1-2001P～2007P 14
- VFNC1S-1001P～1004P 15
- VFNC1S-2002P～2007P 15
- VFNC1-2015P～2022P 15
- VFNC1S-1007P 16
- VFNC1S-2015P～2022P 16
- VFNC1S-2002PL～2007PL 16
- VFNC1S-2015PL～2022PL 17
- Warning 18
- 1.4.2 Inverters 19
- 1.4.4 Installation 22
- ■Installation environment 22
- Resistor 23
- ■How to install 24
- ■Installation location 24
- 2. Connection 27
- Danger 28
- (1) Sink <common: CC> 29
- Control circuit 30
- 1-phase series 30
- 2.3 Description of terminals 33
- 3. Simple operation 37
- : Motor starts 39
- Motor stops (slowdown stop) 39
- : Moves the frequency up 40
- : Moves the frequency down 40
- ■Frequency setting 40
- 4. Basic VF-nC1 operations 42
- 4.1 How to set parameters 43
- 5. Basic parameters 53
- HO 54
- : Meter adjustment 54
- 5.3 Standard default setting 56
- 5.6 Maximum frequency 58
- 5.8 Base frequency 59
- 5.9 Selecting control mode 59
- 6. Extended parameters 65
- Programmable controller 68
- 6.2.4 Jog run 69
- : Sink/Source selection 69
- 6.3 Basic parameters 2 71
- 6.5 Operation frequency 74
- 6.6 DC braking 75
- Jumping resonant frequencies 76
- ” is displayed 77
- • Function 79
- DC voltage 80
- Overvoltage limiting level 80
- 6.11 Performing PI control 81
- 1710 [min 83
- ] for VFNC1 (S)-□□□□P□ type 83
- 6.14 Protection functions 85
- 6.16.2 Free notes 94
- : Free notes 94
- 7. Variety of operation 95
- Press the 98
- key twice 98
- E6581090 100
- Communication 101
- 9.1.1 Abstract 103
- Inverter 104
- Grounding 104
- 10. Peripheral devices 110
- ■Selection of wiring devices 111
- 11.1 User parameters 113
- 11.2 Basic para meters 113
- 11.3 Extended parameters 115
- 12. Specifications 125
- ■External dimensions/weights 128
- ■External dimensions 128
- Before making a service call 129
- 14.1 Regular inspection 137
- 14.2 Periodical inspection 138
- 15. Warranty 141
- 16. Disposal of the inverter 142
© 2020, manymanuals.com. All rights reserved. | 1.605 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals