Toshiba VF-nC1 User Manual Page 56
- Page / 143
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
E6581090
E-4
5
5.3 Standard default setting
V[R
: Standard setting mode selection
Title FunctionAdjustment rangeDefault setting
V[R
Standard setting
mode selection
0 : -
1 : Default setting 50Hz
2 : Default setting 60Hz
3 : Default setting
4 : Trip clear
5 : Cumulative operation time clear
0
★This function will be displayed as 0 during reading on the right. This previous setting is
displayed on the left.
Ex. 3 0
★V[R cannot be set during the inverter operating. Always stop the inverter first and then program.
[Setting values]
50Hz standard setting (V[R=)
To se t the following parameters for a base frequency of 50Hz, set the V[R parameter to 1.
(This setting does not affect the settings of any other parameters.)
• Maximum frequency HJ
: 50Hz
• Base frequency 1 XN
: 50Hz
• Base frequency 2 H
: 50Hz
• Upper limit frequency WN
: 50Hz
• VI/S3 point 2 frequency H
: 50Hz
• Motor rated speed H
: 1410min
-1
60Hz standard setting (V[R=)
To se t the following parameters for a base frequency of 60Hz, set the V[R parameter to 2.
(This setting does not affect the settings of any other parameters.)
• Maximum frequency HJ
: 60Hz
• Base frequency 1 XN
: 60Hz
• Base frequency 2 H
: 60Hz
• Upper limit frequency WN
: 60Hz
• VI/S3 point 2 frequency H
: 60Hz
• Motor rated speed H
: 1710min
-1
Default setting (V[R=)
Setting V[R to will return all parameters to the standard values that were programmed at the
factory.
☆When 3 is programmed, < KPKV will be displayed for a short time after setting and will then
be erased and displayed the original indication “PQ” (Setup parameter). (Only for VFNC1 (S)-
□□□□P□-W type) This setting clears all trip history data but it does not clear cumulative
operation time data. This setting does not affect the settings of the following parameters.
• FM/OUT terminal functions selection HOUN • Meter adjustment HO
• Analog input/logic input function selection H • Sink/source selection H
• Free notes H
See 4.1.1 for setting of setup parameters.
Trip clear (V[R=)
Setting V[R to initializes the past four sets of recorded error history data.
*(The parameter does not change.)
Cumulative operation time clear (V[R=)
Setting V[R to allows the initial resetting of the cumulative operation time monitor (0 [zero]
time).
*(The parameter does not change.)
• Function
Allows setting of all parameters to the standard default setting, etc. at one time. (Except
the setting of HO)
- Industrial Inverter 1
- I. Safety precautions 2
- Danger 4
- Warning 4
- Danger 4
- Warnin 5
- (inverter) 6
- Maintenance and inspection 6
- Disposal 6
- Attach warning labels 7
- ― Contents ― 8
- 1. Read first 10
- [Front panel] 12
- ■Self-up terminal block 13
- VFNC1-2001P～2007P 14
- VFNC1S-1001P～1004P 15
- VFNC1S-2002P～2007P 15
- VFNC1-2015P～2022P 15
- VFNC1S-1007P 16
- VFNC1S-2015P～2022P 16
- VFNC1S-2002PL～2007PL 16
- VFNC1S-2015PL～2022PL 17
- Warning 18
- 1.4.2 Inverters 19
- 1.4.4 Installation 22
- ■Installation environment 22
- Resistor 23
- ■How to install 24
- ■Installation location 24
- 2. Connection 27
- Danger 28
- (1) Sink <common: CC> 29
- Control circuit 30
- 1-phase series 30
- 2.3 Description of terminals 33
- 3. Simple operation 37
- : Motor starts 39
- Motor stops (slowdown stop) 39
- : Moves the frequency up 40
- : Moves the frequency down 40
- ■Frequency setting 40
- 4. Basic VF-nC1 operations 42
- 4.1 How to set parameters 43
- 5. Basic parameters 53
- HO 54
- : Meter adjustment 54
- 5.3 Standard default setting 56
- 5.6 Maximum frequency 58
- 5.8 Base frequency 59
- 5.9 Selecting control mode 59
- 6. Extended parameters 65
- Programmable controller 68
- 6.2.4 Jog run 69
- : Sink/Source selection 69
- 6.3 Basic parameters 2 71
- 6.5 Operation frequency 74
- 6.6 DC braking 75
- Jumping resonant frequencies 76
- ” is displayed 77
- • Function 79
- DC voltage 80
- Overvoltage limiting level 80
- 6.11 Performing PI control 81
- 1710 [min 83
- ] for VFNC1 (S)-□□□□P□ type 83
- 6.14 Protection functions 85
- 6.16.2 Free notes 94
- : Free notes 94
- 7. Variety of operation 95
- Press the 98
- key twice 98
- E6581090 100
- Communication 101
- 9.1.1 Abstract 103
- Inverter 104
- Grounding 104
- 10. Peripheral devices 110
- ■Selection of wiring devices 111
- 11.1 User parameters 113
- 11.2 Basic para meters 113
- 11.3 Extended parameters 115
- 12. Specifications 125
- ■External dimensions/weights 128
- ■External dimensions 128
- Before making a service call 129
- 14.1 Regular inspection 137
- 14.2 Periodical inspection 138
- 15. Warranty 141
- 16. Disposal of the inverter 142
© 2020, manymanuals.com. All rights reserved. | 4.284 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals