Toshiba VF-nC1 User Manual Page 57
- Page / 143
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
E6581090
E-5
5
5.4 Selecting forward and reverse runs (operation panel only)
HT
: Forward/reverse selection (Operation panel)
[Parameter setting]
Title Function Adjustment range Default setting
HT
Forward/reverse selection
(Operation panel)
0: Forward run
1: Reverse run
0
★Check the direction of rotation on the status monitor.
HTH : Forward run HTT : Reverse run ⇒ For monitoring,
see 8.1.
★When the F and R terminals are used for switching between forward and reverse
rotation from the terminal board, the HT forward/reverse run selection is rendered
invalid.
Short across the F-CC terminals: forward rotation
Short across the R-CC terminals: reverse rotation
★This function is valid only when EOQF is set to K (operation panel).
5.5 Setting acceleration/deceleration time
CEE
: Acceleration time 1 (s)
FGE
: Deceleration time 1 (s)
Set acceleration time from 0Hz operation frequency to maximum frequency HJ and deceleration
time as the time when operation frequency goes from maximum frequency HJ to 0Hz.
O
utput frequency (Hz)
FGE
CEE
HJ
Time (s)
0
[Parameter setting]
Title Function Adjustment range Default setting
CEE
Acceleration time 1 (s) 0.1-3000 seconds 10.0
FGE
Deceleration time 1 (s) 0.1-3000 seconds 10.0
☆If the programmed value is shorter than the optimum acceleration/deceleration time determined
by load conditions, overcurrent stall or overvoltage stall function may make the
acceleration/deceleration time longer than the programmed time. If an even shorter
acceleration/deceleration time is programmed, there may be an overcurrent trip or overvoltage
trip for inverter protection. (For further details, see 13.1).
• Function
1) For acceleration time CEE, program the time that it takes for the inverter output
frequency to go from 0Hz to maximum frequency HJ.
2) For deceleration time FGE, program the time that it takes for the inverter output
frequency to go from maximum frequency HJ to 0Hz.
• Function
Program the direction of rotation when the running and stopping are made using the RUN
key and STOP key on the operation panel. Valid when EOQF (command mode) is set to
1 (operation panel).
- Industrial Inverter 1
- I. Safety precautions 2
- Danger 4
- Warning 4
- Danger 4
- Warnin 5
- (inverter) 6
- Maintenance and inspection 6
- Disposal 6
- Attach warning labels 7
- ― Contents ― 8
- 1. Read first 10
- [Front panel] 12
- ■Self-up terminal block 13
- VFNC1-2001P～2007P 14
- VFNC1S-1001P～1004P 15
- VFNC1S-2002P～2007P 15
- VFNC1-2015P～2022P 15
- VFNC1S-1007P 16
- VFNC1S-2015P～2022P 16
- VFNC1S-2002PL～2007PL 16
- VFNC1S-2015PL～2022PL 17
- Warning 18
- 1.4.2 Inverters 19
- 1.4.4 Installation 22
- ■Installation environment 22
- Resistor 23
- ■How to install 24
- ■Installation location 24
- 2. Connection 27
- Danger 28
- (1) Sink <common: CC> 29
- Control circuit 30
- 1-phase series 30
- 2.3 Description of terminals 33
- 3. Simple operation 37
- : Motor starts 39
- Motor stops (slowdown stop) 39
- : Moves the frequency up 40
- : Moves the frequency down 40
- ■Frequency setting 40
- 4. Basic VF-nC1 operations 42
- 4.1 How to set parameters 43
- 5. Basic parameters 53
- HO 54
- : Meter adjustment 54
- 5.3 Standard default setting 56
- 5.6 Maximum frequency 58
- 5.8 Base frequency 59
- 5.9 Selecting control mode 59
- 6. Extended parameters 65
- Programmable controller 68
- 6.2.4 Jog run 69
- : Sink/Source selection 69
- 6.3 Basic parameters 2 71
- 6.5 Operation frequency 74
- 6.6 DC braking 75
- Jumping resonant frequencies 76
- ” is displayed 77
- • Function 79
- DC voltage 80
- Overvoltage limiting level 80
- 6.11 Performing PI control 81
- 1710 [min 83
- ] for VFNC1 (S)-□□□□P□ type 83
- 6.14 Protection functions 85
- 6.16.2 Free notes 94
- : Free notes 94
- 7. Variety of operation 95
- Press the 98
- key twice 98
- E6581090 100
- Communication 101
- 9.1.1 Abstract 103
- Inverter 104
- Grounding 104
- 10. Peripheral devices 110
- ■Selection of wiring devices 111
- 11.1 User parameters 113
- 11.2 Basic para meters 113
- 11.3 Extended parameters 115
- 12. Specifications 125
- ■External dimensions/weights 128
- ■External dimensions 128
- Before making a service call 129
- 14.1 Regular inspection 137
- 14.2 Periodical inspection 138
- 15. Warranty 141
- 16. Disposal of the inverter 142
© 2020, manymanuals.com. All rights reserved. | 0.443 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals