Toshiba Tosvert VF-AS1 User Manual Page 196
- Page / 312
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
E6581301
G-2
7
7.2 Applied operation with input and output signals (operation by terminal board)
7.2.1 Functions of input terminals (in case of sink logic)
Use the above parameters to send signals from an external programmable controller to various control input terminals
to operate and/or set the inverter.
The desired contact input terminal functions can be selected from 120 types. This gives system design flexibility.
[Control terminal board]
■ Setting of contact input terminal function
Term inal
symbol
Title Function
Adjustmen
t range
Default setting
-
H, H,
H
Always ON function selection 1~3 (No function is
assigned)
F H Input terminal function selection 1 (F) (Forward run)
R H Input terminal function selection 2 (R) (Reverse run)
ST H Input terminal function selection 3 (ST) (Standby)
RES H Input terminal function selection 4 (RES) (Reset)
S1 H Input terminal function selection 5 (S1) (Preset speed 1)
S2 H Input terminal function selection 6 (S2) (Preset speed 2)
S3 H Input terminal function selection 7 (S3) (Preset speed 3)
RR/S4 H Input terminal function selection 8 (RR/S4) (Preset speed 4)
LI1~LI8 H~H Input terminal function selection 9~16
B12~B15 H~H Input terminal function selection 17~20
~
⇒ Refer
to Section
7.2.1.
Note: When H, H and H (Always ON function selection 1~3) are selected, selected function is
generally activated regardless of positive or negative logic.
Note: H~H is for use of expansion terminal board option unit.
Note: H~H is for use of 16 bit binary board option unit.
■ Connection method
1) In case of positive logic (a-contact) input
Inverter
A-contact switch
CC
Input terminal
+
This function is activated when the input
terminal and CC (common) are short-circuited.
Use this function to specify forward/reverse
run or a preset speed operation.
2) In case of negative logic (b-contact) input
B-contact switch
CC
Input terminal
+
This function is activated when the input
terminal and CC (common) are open-circuit.
Use this function to specify operation standby
signal or reset signal.
Inverter
- E6581301Ԙ 1
- I. Safety precautions 3
- Danger 4
- II. Introduction 9
- E6581301 11
- - Contents 11
- 1. Read first 17
- 1.3.1 Names and functions 18
- 1) Outside view 18
- 1.3.2 Detaching the cover 25
- 1.4 Notes on the application 30
- 1.4.1 Motors 30
- 1.4.2 Inverters 32
- ■ Disposal 32
- Warning 33
- 1.4.4 Installation 35
- ■ Installation environment 35
- ■ How to install 36
- 2. Connection equipment 41
- 2.2 Standard connections 43
- 2.3 Description of terminals 48
- 3. Operations 55
- Status monitor mode 56
- Standard monitor mode 56
- (when the power is turned on) 56
- Setting monitor mode 56
- Deceleration 57
- 3.2.2 Panel operation 61
- 4.1 How to set parameters 64
- 5. Basic parameters 67
- CW : Automatic torque boost 69
- ■ Preset speed operation 74
- + The inverter is factory 75
- +To save the frequency 75
- HE and the set 75
- 5.6 Selecting control mode 77
- 2) Decreasing output voltage 78
- 3) Increasing starting torque 78
- 5.8 Base frequency 81
- 5.9 Maximum frequency 82
- Estimation of temperature 90
- 5.17 PWM carrier frequency 96
- Warning 97
- Surge killer 103
- 5.20 Standard default setting 107
- ( ) 109
- 5.22 EASY key function 110
- 6. Extended parameters 113
- 6.2 Input signal selection 115
- Internal command 116
- Servo lock status 120
- Command selected 123
- Operation frequency 125
- 6.8 DC braking 126
- 6.10 Jog run mode 131
- Jumping width 2 135
- Jumping width 1 135
- 6.14.1 Retry function 136
- 6.15 Drooping control 139
- Load portion torque input 141
- 6.20 PID control 145
- 6.22 Setting motor constants 148
- Setting motor constants 150
- 6.24 Torque control 152
- 6.25 Torque limit 154
- Positive torque 155
- Negative torque 155
- • Function 158
- 6.31 Pattern operation 163
- 6.32 Preset speed mode 165
- 6.33 Protection functions 166
- 6.33.3 Emergency stop 167
- H : Emergency stop 167
- 6.34 Override 175
- 6.35 Adjustment parameters 177
- Function 179
- ■ Example of setting 1 181
- ■ Example of setting 2 181
- 6.37 Tracing functions 183
- Trace data 1 184
- Trigger input 184
- 6.38 Communication function 187
- 1) 2-wire RS485 188
- 2) 4-wire RS485 190
- Host computer 191
- 6.39 My function 193
- 6.40 Traverse function 194
- 7.1 External operation 195
- B-contact switch 196
- Input terminal 196
- Inverter 196
- Programmable controller 197
- 7.2.4 Analog input filter 203
- 8.2 Monitoring the status 210
- 8.4.1 Trip code display 216
- 9.1.1 EMC directive 221
- Contact your supplier 222
- Use the 224
- EMC FILTER 226
- Ferrite core 1 227
- Shielded cable or [Note 1] 227
- Noise cut plate 228
- AIC, Fuse and Wire sizes 229
- Ｅ６５８１３００ 232
- Note on wiring 233
- 11. Table of parameters 239
- 12. Specifications 285
- E6581301 286
- ■ Outside dimensions and mass 289
- (Installation dimension) 290
- Before making a service call 295
- Cautions about cleaning 303
- 14.2 Periodical inspection 304
- ■ Check items 304
- 15. Warranty 307
- Warning 309
Related products and manuals for Tools Toshiba Tosvert VF-AS1
Tools Toshiba HX7 User Manual
(6 pages)
(6 pages)
Tools Toshiba MBSB80-225-43 User Manual
(1 pages)
(1 pages)
Tools Toshiba 1500 Plus User Manual
(31 pages)
(31 pages)
Tools Toshiba G8000 User Manual
(79 pages)
(79 pages)
Tools Toshiba G3 Plus Pack User Manual
(4 pages)
(4 pages)
Tools Toshiba 1000 Series User Manual
(2 pages)
(2 pages)
Tools Toshiba Power Supply User Manual
(2 pages)
(2 pages)
Tools Toshiba Dura-Bull TX User Manual
(6 pages)
(6 pages)
Tools Toshiba 4200FA Series User Manual
(2 pages)
(2 pages)
Tools Toshiba QX7 Series User Manual
(6 pages)
(6 pages)
Tools Toshiba G3 TOSVERT-130 User Manual
(62 pages)
(62 pages)
Tools Toshiba 4200FA CT/XT User Manual
(68 pages)
(68 pages)
Tools Toshiba 1700 Series User Manual
(2 pages)
(2 pages)
Tools Toshiba 1600 XP UPS User Manual
(4 pages)
(4 pages)
Tools Toshiba Tosvert RS485 User Manual
(73 pages)
(73 pages)
© 2020, manymanuals.com. All rights reserved. | 0.904 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals