Toshiba TDP-TW100 User Manual download pdf (Page 14)

Operations

Projector placement angle adjustments

The placement angle and the height of the projected image can be adjusted by the foot

adjuster.

q Lift up the front of the projector to

the desired angle, then press the

foot adjuster release button.

The foot adjuster extends. Release the

button to lock the position.

w To fine adjust the angle, twist the

foot adjuster.

e To adjust the horizontal angle, use

the right and left tilt adjusters.

•To stow the foot adjuster, hold up the projector while pressing the foot adjuster

release button, then slowly lower the projector.

Adjusting the screen size and focus

Use the ZOOM button to adjust the screen size.

Use the FOCUS button to adjust the screen focus.

Adjusting the volume with the

buttons

The speaker volume can be adjusted when an audio signal is being input.

Notes

• While a text entry screen (e.g., the Password entry screen) is displayed, the remote

control’s FOCUS and ZOOM buttons function as numeric keys, and therefore cannot be

used to adjust the screen size or focus. In such a case, use the FOCUS and ZOOM

buttons on the projector to make adjustment or retry after quitting the text entry screen.

• Note that lamp characteristics may rarely cause the brightness to fluctuate slightly.

•A lamp is consumable item. If used for extended periods, images will appear dark, and

the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The

lifetime of the lamp depends on conditions of use.)

• The DMD

is made using extremely advanced technology, but there may be black spots

(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. Please

note that these are not malfunctions.

• Although this projector supports a wide range of RGB signals

p.87

, any resolutions not

supported by this projector (XGA) will be expanded or shrunk, which will affect image

quality slightly. To view high-quality images, it is recommended that the computer’s

external output should be set to XGA resolution.

• With some models of computer having LCD displays or the like, displaying images

simultaneously on the projector and the monitor’s display may prevent the images from

displaying properly. If this happens, turn off the computer’s LCD display. For information

on how to turn off the LCD display, see the owner’s manual of your computer.

• If no signal is being input from the connected equipment or signal input is stopped while

projecting, the “No signal” will appear.

• If a signal not supported by the projector is input, the “Unsupport signal” will appear.

• If an unavailable operation button is pressed, the

icon will appear.

Control panel

Remote

Control

Turn on the power.

Tu rn on the power by following the instructions in “Turning the power on”

p.24

The Easy setup function works to automatically adjust the screen focus and correct the

keystone distortion. If RGB signals are input, auto-setting is also made. This operation

does not take place when [Easy setup] in the Default setting menu is [Off]

p.41

Select the language and the lamp power (When using the

first time).

When the projector is used for the first time after purchase, the start menu for lan-

guage (to display the menus and messages on the screen) and lamp power selection

and configuration is displayed in English. (If the screen is out of focus, adjust it

according to the step

q Use the or button to select the

desired language and press the

button.

Message for setup confirmation is displayed in a

selected language.

Then, the menu for lamp power selection and

configuration is displayed. It is automatically set as

Standard. To change the setting, follow the step w.

w Use the or button to select the lamp

power and press the

button.

The lamp power, if selected, will be toggled without

pressing the

button. The display automatically

disappears in a few seconds.

Notes

• When the projector is turned on the next time, the start menu does not appear upon

startup. However, if [Reset all] is executed from the Default setting menu

p.41

, the

start menu will be displayed the next time when the power is turned on.

• The language can also be set via the Display setting menu

p.38

and Lamp power

via the Default setting menu

p.41

• This owner’s manual assumes that English has been selected.

Activate the connected device.

Tu rn on and start the connected device such as a computer.

Press the INPUT button.

An image of the connected equipment is projected.

Each time you press the INPUT button, it switches to the input of the connected

equipment that is outputting video signals.

Notes

• When [Auto input search] is set to [Off] in the Default setting menu

p.41

(factory

setting is [On]), the Input select menu appears if you press the INPUT button

p.42

• If no signal is being output from the connected equipment, pressing the INPUT button

does not change the input and “There is no other input signal.” will appear.

Basic operations

English

French

German

Italian

Spanish

Portuguese

Russian

Swedish

Tur kish

Polish

Japanese

Chinese (simplified)

Chinese (traditional)

Korean

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 45 46

Comments to this Manuals

No comments

Toshiba TDP-TW100 User Manual Page 14

Comments to this Manuals

Related products and manuals for Projectors Toshiba TDP-TW100