TEC Label PrinterB-450-HS-QQ SERIESOwner’s ManualTable of Contents
4-14. DIP SWITCH FUNCTIONSEO1-330194. DIP SWITCH FUNCTIONSThe DIP switches are located at the rear of the printer.4. DIP SWITCH FUNCTIONSDIP SWFig. 4-
5-15. SET UP PROCEDUREEO1-330195. SET UP PROCEDURE5.1 REQUIREMENTS FOR OPERATIONThis machine has the following requirements:• The host computer must h
6-16. INSTALLATION PROCEDURE EO1-330196. INSTALLATION PROCEDURE6.1 INSTALLING THE SUPPLY HOLDER UNIT6.1 INSTALLING THE SUPPLY HOLDER UNITFit the two s
6-26. INSTALLATION PROCEDURE EO1-33019Fig. 6-3Power CordSerial Interface (RS-232C)WARNING!Turn the POWER SWITCH to OFF before connecting the power cor
7-17. LOADING THE RIBBONEO1-330197. LOADING THE RIBBON7. LOADING THE RIBBONFig. 7-2Fig. 7-1Print Head BlockHead Release LeverTop Cover3. Fit the protr
7-27. LOADING THE RIBBONEO1-330197. LOADING THE RIBBON5. Set the ribbon core (supply side) by fitting the protrusion into the notch.6. Turn the guide
8-1EO1-3300198. LOADING THE PAPER8. LOADING THE PAPER8. LOADING THE PAPER3. Set the supply holders to both sides of the paper roll.Fig. 8-1Supply Hold
8-2EO1-3300198. LOADING THE PAPER8. LOADING THE PAPER4. Put the paper roll and supply holders on the supply holder unit.NOTE: The paper must be loaded
8-3EO1-3300198. LOADING THE PAPER8. LOADING THE PAPER10. For details on changing the black mark sensor position according to the black mark position,
8-4EO1-3300198. LOADING THE PAPER8. LOADING THE PAPER13. Close the top cover, and then attach the supply cover to the supply holder unit. (Refer to s
Copyright © 2000by TOSHIBA TEC CORPORATIONAll Rights Reserved570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPANThis equipment has been tested and
8-5EO1-3300198. LOADING THE PAPER8. LOADING THE PAPER Setting the black mark sensor position1 Fold over the end of the label. Then, move sensor knob
8-6EO1-3300198. LOADING THE PAPER8. LOADING THE PAPER Setting the feed gap sensor position1 Move sensor knob A in a horizontal direction so that the
9-1EO1-330199. THRESHOLD SETTING9. THRESHOLD SETTINGFor the printer to maintain a constant print position it uses the transmissive sensor to measure
10-1EO1-3301910. CARE/HANDLING OF THE PAPER AND RIBBON10. CARE/HANDLING OF THE PAPER AND RIBBON10. CARE/HANDLING OF THE PAPER AND RIBBON• Do not store
11-1EO1-3301911. GENERAL MAINTENANCE11. GENERAL MAINTENANCE11.1 CLEANINGTo help retain the high quality and performance of your printer it should be r
11-2EO1-3301911. GENERAL MAINTENANCE11.2 COVERS6. Clean the platen with a cloth moistened with alcohol.7. With a soft cloth, remove any dust or glue f
11-3EO1-3301911. GENERAL MAINTENANCE11.3 REMOVING JAMMED PAPER11.3 REMOVING JAMMED PAPER1. Turn the power off.2. Open the top cover.3. Move the head
11-4EO1-3301911. GENERAL MAINTENANCE11.3 REMOVING JAMMED PAPER2. Fit the enclosed Allen Key into the right side of the cutter unit to rotate the cutt
12-1EO1-3301912. TROUBLESHOOTING12. TROUBLESHOOTING12. TROUBLESHOOTINGSolution1. Reload the paper correctly.→ Press the [PAUSE] key.2. Remove the caus
12-2EO1-3301912. TROUBLESHOOTING12. TROUBLESHOOTINGSolution1. Restart the printing by pressingthe [PAUSE] key.2. Replace the print head.Remove the jam
(i)Safety SummaryEO1-33019Safety SummaryPersonal safety in handling or maintaining the equipment is extremely important. Warnings and Cautionsnecessa
13-1EO1-33019APPENDIXAPPENDIXAPPENDIX ASCII Code Chart Font Sample Barcode Sample
14-1EO1-33019INDEXINDEXINDEXAAC Power inlet... 3-1Auto media feed ... 4-1BBar c
PRINTED IN JAPANEO1-33019E
(ii)Safety SummaryEO1-33019CAUTIONThis indicates that there is the risk of personal Injury or damage toobjects if the machines are improperly handled
TABLE OF CONTENTS1. INTRODUCTION ...1- 11.1 APPLICABLE MODEL ...
1-11. INTRODUCTIONEO1-330191.1 APPLICABLE MODEL1. INTRODUCTIONThank you for choosing the TEC B-450 Series thermal transfer printer. This new generati
2-12. SPECIFICATIONSEO1-33019Supply voltage 100 - 120V, 60HzPower consumption 1.8 A, 140 W max. (standby: 0.22 A, 13.5 W)Operating temperature 5˚C ~
2-22. SPECIFICATIONSEO1-330192.3 PAPER (LABEL) SPECIFICATIONS2.3 PAPER (LABEL) SPECIFICATIONSNOTES: 1. To ensure good print quality and maximum print
3-13. APPEARANCEEO1-330193. APPEARANCE3.1 FRONT/REAR VIEW3.1 FRONT/REAR VIEWFront View Rear View3.2 OPERATION PANELPOWER LED (Green)Lights when the po
Comments to this Manuals