Toshiba Tecra R850 User Manual

User's ManualR850/R840/R830

Disposing of the computer and the computer'sbatteriesDiscard this computer in accordance with applicable laws andregulations. For further informa

SD, SDHC and SDXC memory cards appear the same externally.However, the logo on memory cards is different, so pay carefulattention to the logo when pur

The card is designed so that it can be inserted only one way. Do nottry to force the card into the slot.Do not leave a card partially inserted in the

Figure 3-13 Inserting a memory media (R830)211. Memory media slot 2. Memory mediaMake sure memory media is oriented properly before you insert it. Ify

Additional memory moduleYou can install additional memory into the computer in order to increasethe amount of system memory that is available. This se

2. Remove the AC adaptor and all cables and peripherals connected tothe computer.3. Close the display panel.4. Turn the computer upside down and remov

7. Align the notch of the memory module with that of the memory slotand gently insert the module into the slot at about a 30 degree anglebefore holdin

8. Seat the memory module cover in place and secure it with thescrew(s).Take care to ensure that the memory module cover is firmly closed.Figure 3-16

8. Grasp the module by its edges and remove it from the computer.If you use the computer for a long time, the memory modules and thecircuits locating

2. Connect the monitor cable to the External RGB monitor port.Figure 3-18 Connecting the monitor cable to the External RGB monitor port(R830)121. Exte

As the port operation of all HDMI (High-Definition Multimedia Interface)monitors have not been confirmed, some HDMI monitors may not functionproperly.

Use of controls, adjustments or the performance of procedures otherthan those specified may result in hazardous radiation exposure.To prevent direct e

When you change the display output device by hot key like FN + F5,the playback device may not switch automatically. In this case, inorder to set the p

Display mode at List All Modes HD Format720 by 480, True Color (32bit), 60Herts 480pThe above display mode is a typical HDMI display mode. The selecta

Make sure the connector is properly aligned with the socket.Do not try to force the connection, doing so can damage the connectingpins.Figure 3-20 Con

TOSHIBA Hi-Speed Port Replicator IIIn addition to the ports available on the computer, the TOSHIBA Hi-SpeedPort Replicator II also provides several ki

Figure 3-21 Security lock (R830)11. Security lock slotOptional TOSHIBA AccessoriesYou are able to add a number of options and accessories in order to

To launch the Volume Mixer utility, right click on the speaker icon onthe Taskbar, and select Open Volume Mixer from the sub menu.To adjust the volume

Power ManagementThe audio controller in your computer can be turned off when the audiofunction is not used. To adjust the configuration of audio power

You can clean the display screen by spraying a small amount of glasscleaner onto a soft, clean cloth and then wiping the screen gently withthe cloth.N

When the processor's temperature falls within normal range, the fan will beturned off and the processor operation returned to its standard speed.

Chapter 4Utilities & Advanced UsageThis chapter describes the utilities and special features in this computer,and the advanced usage of some utili

PrecautionsCAUTION: This appliance containsa laser system and is classified as a“CLASS 1 LASER PRODUCT.” Touse this model properly, read theinstructio

TOSHIBA Accessibili-tyThe TOSHIBA Accessibility utility providessupport to movement impaired users when theyneed to use the TOSHIBA Hot-key functions.

TOSHIBA VIDEOPLAYERThis software is provided for playback of Video.It has an on-screen interface and functions. ClickStart -> All Programs -> TO

TOSHIBA Disc Crea-torYou can create discs in a number of formatsincluding audio discs that can be played on astandard disc player, and data discs whic

TOSHIBA BulletinBoardBulletin Board is a convenient place to pin thingsto visually organize in a fun and creative way.Simply drag and drop your favori

2. Set the TPM in the Security tab to Enabled3. Press the F10 key.4. Press the Y key to accept the changes. The computer will restart.In order to chan

Keypad overlay A ten-key numeric keypad is integrated into thekeyboard. Please refer to the Keypad overlaysection in Chapter 3, Operating Basics, fori

Hibernation Mode This feature lets you turn off the power to thecomputer without exiting from your software. Thecontents of main memory are automatica

Sleep and ChargeYour computer can supply USB bus power (DC5V) to the USB port evenwhen the power of the computer is turned OFF. "Power OFF"

Metal paper clips or hair pins/clips will generate heat if they come intocontact with USB ports. Do not allow USB ports to come into contact withmetal

TOSHIBA Face Recognition does not guarantee the correctidentification of a user. Changes to the likeness of a registrant, suchas hair style changes, w

PrefaceCongratulations on your purchase of this computer. This powerful notebookcomputer provides excellent expansion capability, includes multimediaf

The Management screen is displayed for a logged-in user whose facehas already been registered.2. Click Run as administrator in lower left of the Manag

3. Click the Delete button. "You are about to delete the user data. Wouldyou like to continue?" will be displayed on the screen.If you do no

7. Verification will be performed. If the authentication is successful, theimage data taken in step 6 will be faded in and placed over oneanother.If a

Delete (button)Click this button to delete a registered password. Before you candelete a password, you must first enter the current password correctly

Set, delete or change the Supervisor Password.Specify restrictions for general users.Starting the computer by passwordIf you have already registered a

OK Accepts your changes and closes the HW Setupwindow.Cancel Closes the window without accepting yourchanges.Apply Accepts all your changes without cl

Dynamically Switcha-bleThe processor's power consumption andautomatic clock speed switching functions areenabled - in use the processor's op

If a Supervisor Password has been set, manual boot device selectionfunctions may be restricted.The boot device selection methods described above will

Disabled Disables the Wake-up on Keyboard function.(Default)LANWake-up on LANThis feature lets the computer's power be turned on from shutdown wh

Disabled Disabled Disables the USB Legacy Emulation.SATAThis feature allows you to set conditions for SATA.eSATAThis feature allows you to enable/disa

Display ABC Names of windows or icons or text generated bythe computer that appear on its display screen arepresented in the type face you see to the

This information is used to identify and provide a notification of systemconditions which may effect the performance of your TOSHIBA computer. Itmay a

Using the Hard Disk Drive (HDD) ProtectionThis computer has a function for reducing the risk of damage on the harddisk drive.Using an acceleration sen

Detection LevelThis function can be set to four levels. The sensitivity levels in whichvibrations, impacts and their similar signs are detected can be

HDD Protection MessageSpecify whether to display a message when TOSHIBA HDD Protection isactive.This function does not work when the computer is booti

Creating Recovery MediaThis section describes how to create Recovery Media.Be sure to connect the AC adaptor when you create Recovery Media.Be sure to

5. After Recovery Media Creator starts, select the type of media and thetitle you wish to copy, and then click the Create button.Restoring the pre-ins

If you have not created "Recovery Media", please contact TOSHIBAsupport for assistance.Restoring the pre-installed software from theRecovery

Computer LCD YesRGB YesDisplayPort YesDisplayPort Model With TOSHIBA Hi-Speed Port Replicator II:Computer LCD Yes Yes Yes - -RGB - - - - -DisplayPort

Chapter 5Power and Power-Up ModesThe computer's power resources include the AC adaptor, battery pack andany internal batteries. This chapter prov

Power on Power off(no operation)AC adaptornotconnectedBattery charge isabove lowbattery triggerpoint• Operates• LED:Battery offDC IN offBattery ch

LCD Model name Short Name35.6cm(14.0")TECRA R840/Satellite Pro R840/Satellite R840 R84033.8cm(13.3")PORTÉGÉ R830/Satellite R830 R830R850/R84

temperature falls to a normal range, charging will resume - this process willoccur regardless of whether the computer's power is on or off.DC IN

Before you remove the battery pack, save your data and shut down thecomputer, or place the computer into Hibernation Mode. Please be awarethat, when p

Charge the battery pack only in an ambient temperature between 5and 35 degrees Celsius. Otherwise, the electrolyte solution might leak,battery pack pe

Charging Time (hours) for R830/R840 seriesBattery type Power off Power onBattery pack (66Wh, 6cell)about 5 about 5 ~15Battery pack (93Wh, 9cell)about

You should wait at least 16 seconds after turning on the computerbefore trying to monitor the remaining operating time. This is becausethe computer ne

Retention Time for R850 seriesBattery type Sleep Mode Shut Down ModeBattery pack (48Wh, 6cell)about 4 days about 75 daysBattery pack (66Wh, 6cell)abou

3. Operate the computer on battery power for five minutes. If you findthat the battery pack has at least five minutes of operating time,continue opera

2. Turn the computer's power off - ensure that the Power indicator is off.3. Remove all cables and peripherals that are connected to thecomputer.

Windows utilitiesYou can configure various settings associated with both Sleep Mode andHibernation Mode within the Power Options (to access it, Start

Chapter 6TroubleshootingTOSHIBA have designed this computer for durability, however, shouldproblems occur you are able to use the procedures detailed

General PrecautionsTOSHIBA computers are designed to optimize safety, minimize strain andwithstand the rigors of portability. However, certain precaut

Check all cables to ensure they are correctly and firmly attached to thecomputer - loose cables can cause signal errors.Inspect all connecting cables

Hardware If you cannot find a software problem, you shouldthen check the setup and configuration of yourhardware. First run through the items in thepr

indicator is glowing, the computer is connected to a live external powersource.Hardware and system checklistThis section discusses problems caused by

AC powerIf you have trouble turning on the computer with the AC adaptor connectedyou should check the status of the DC IN indicator.Please refer to Ch

Problem ProcedureBattery doesn’tcharge when the ACadaptor is attached(Battery indicatordoes not gloworange).If the battery is completely discharged, i

Real Time ClockProblem ProcedureThe followingmessage isDisplayed on thescreen: RTC Power Failure. Check system. Then press [F2] key. The charge in the

Problem ProcedureNo display Press the FN + F5 hot keys to adjust the displaypriority, and to make sure it is not set for output toan external monitor.

Problem ProcedureYou cannot access adisc in the drive.Make sure the drive’s disc tray is securely closed.Press gently until it clicks into place.Open

Problem ProcedureSmart Card erroroccursRemove the Smart Card from the computer, makesure to confirm that the card oriented correctly andreinsert it in

Problem ProcedureThe reaction ofTouch pad is eithertoo sensitive or notsensitive enough.Adjust the touch Sensitivity.To access it, click Start -> C

Stress injuryCarefully read the Instruction Manual for Safety and Comfort. It containsinformation on the prevention of stress injuries to your hands a

Fingerprint SensorProblem ProcedureReading of thefingerprint was notsuccessful.In this instance you should try the fingerprintreading operation again

Problem ProcedureI cannot use theSleep and Chargefunction.Sleep and Charge function may be disabled.Select the "Enable Sleep and Charge" che

Problem ProcedureThe "USB Wakeupfunction" does notwork.When Sleep and Charge function is enabled, the"USB WakeUp" function does no

Problem ProcedureIf there is a memorymalfunction, thePower indicator willrepeatedly flash (onfor 0.5 seconds, offfor 0.5 seconds) inthe followingpatte

Problem ProcedureAnnoying sound isheardIn this instance you may be experiencing feedbackfrom either the internal microphone or an externalmicrophone c

Problem ProcedureNo display Try adjusting the contrast and brightness controlson the external monitor.Press the FN + F5 hot key in order to change the

Wireless LANIf the following procedures do not restore LAN access, consult your LANadministrator. For more information on wireless communication, refe

If a problem occurs when you are running software applications,consult the software documentation for troubleshooting suggestionsand consider calling

Appendix ASpecificationsThis appendix summarizes the computer’s technical specifications.Physical DimensionsPhysical Dimensions shown below do not inc

External RGB monitor port pin assignment610151511Pin Signal Name Description I/O1 CRV Red Video Signal O2 CGV Green Video Signal O3 CBV Blue Video Sig

Chapter 1Getting StartedThis chapter provides an equipment checklist, and basic information tostart using your computer.Some of the features described

Appendix BAC Power Cord and ConnectorsThe power cord’s AC input plug must be compatible with the variousinternational AC power outlets and the cord mu

For the United States and Canada, two pin plug configuration must be a2-15P (250V) or 1-15P (125V) and three pin plug configuration must be6-15P (250V

Appendix CLegal FootnotesThis chapter states the Legal Footnotes information applicable to TOSHIBAcomputers.Non-applicable IconsCertain computer chass

conditions. Read additional restrictions in your product documentation.Contact TOSHIBA technical service and support, refer to Troubleshootingsection

achieved on select models and configurations tested by TOSHIBA at thetime of publication. Recharge time varies depending on usage. Battery maynot char

Copy ProtectionApplicable copy protection standards included in certain media mayprevent or limit recording or viewing of the media.R850/R840/R830User

Appendix DInformation for Wireless DevicesWireless LAN InteroperabilityThe Wireless LAN is compatible with other LAN systems Direct SequenceSpread Spe

Please visit http://www.pc.support.global.toshiba.com, if you have anyquestions about using Wireless LAN or Bluetooth Card from TOSHIBA.In Europe visi

Italy: - For private use, a generalauthorization is required if WAS/RLAN’s are used outside ownpremises. For public use, a generalauthorization is req

Restrictions for Use of 5470-5725MHz Frequencies in EuropeItaly: - For private use, a generalauthorization is required if WAS/RLAN’s are used outside

TOSHIBA Resolution+ Plug-in For Windows Media PlayerTOSHIBA eco UtilityTOSHIBA Bulletin BoardTOSHIBA ReelTimeTOSHIBA HW Setup UtilityTOSHIBA Value Add

designed to provide reasonable protection against harmful interference in aresidential installation.Refer to the FCC information section for the detai

Using this equipment in JapanIn Japan, the frequency bandwidth of 2,400MHz to 2,483.5MHz for secondgeneration low-power data communication systems suc

4. : This equipment uses a frequency bandwidth from 2,400MHz to 2,483.5 MHz. It is impossible to avoid the band of mobileobject identification system

Intel® Centrino® Wireless-N + WiMAX 6150 Wireless LAN and WiMAXThe Name of the radio equipment: 612BNXHMWDSP Research, Inc.Approval Number: D100898003

Albania Australia Austria AzerbaijanArgentina Bahrain Belgium BoliviaBosnia andHerzegovinaBulgaria Canada CambodiaChile China Colombia Costa RicaCroat

Do not use this equipment in the countries/regions which are not listed inthe table below.An ad-hoc mode is not available in 802.11a and 802.11n mode.

South Korea Spain Sri Lanka SwedenSwitzerland Tanzania Thailand Trinidad andTobagoTurkey UK Uruguay USAZimbabweApproved Countries/Regions for the Inte

Lithuania Luxemburg Malawi MalaysiaMalta Mexico Montenegro MonacoNepal Netherlands New Zealand NicaraguaNorway Oman Pakistan Papua NewGuineaParaguay P

Cyprus Czech Republic Denmark DominicanRepublicEcuador Estonia Finland FranceGermany Ghana Greece Hong KongHungary Iceland India IndonesiaIreland Ital

Approved Countries/Regions for the Intel® Centrino®Wireless-N + WiMAX 6150 Wireless LAN and WiMAXThis equipment is approved to the radio standard by t

Table of ContentsPrefaceGeneral PrecautionsChapter 1Getting StartedEquipment checklist ...

Before you install a device or application, save any data in memory tothe hard disk drive or other storage media. Failure to do so may resultin the lo

Bermuda Bolivia Bosnia andHerzegovinaBrazilBulgaria Canada Chile ChinaColombia Costa Rica Cyprus CzechRepublicDenmark El Salvador Estonia FinlandFranc

Australia Austria Azerbaijan BahrainBangladesh Belarus Belgium BoliviaBosnia andHerzegovinaBotswana Brazil BulgariaBurkina Faso Burundi Cambodia Camer

South Africa South Korea Spain Sri LankaSwaziland Sweden Switzerland TaiwanTajikistan Thailand Togo TunisiaTurkey Turkmenista UAE UKUkraine Uruguay US

New Zealand Nicaragua Nigeria NorwayOman Pakistan Panama Papua NewGuineaParaguay Peru Philippines PolandPortugal Puerto Rico Qatar RomaniaRussia Saudi

IndexAAC adaptoradditional 3-49connecting 1-3DC IN 19V jack 2-3, 2-14,2-25 ASCII characters 3-8BBatteryextending life 5-8monitoring capacity 5-6real t

External RGB monitor 2-14,2-25FFingerprint Sensorproblems 6-12using 3-8 FN + 1 ( reduce) 3-6FN + 2 (enlarge) 3-6FN + 3 (Volume down) 3-6FN + 4 (Volume

Function keys F1...F12 3-3Hot key functions 3-4problems 6-7Windows special keys 3-6 Keypad overlayArrow mode 3-7Numeric mode 3-7temporarily using norm

Hardware and systemchecklist 6-4Internal display panel 6-7Keyboard 6-7LAN 6-17Memory Media Card 6-9Optical Disc Drive 6-8Overheating powerdown 6-4Powe

Wireless WANindicator 2-3, 2-13, 2-24 R850/R840/R830User's Manual Index-5

Never place your computer or AC adaptor on a wooden surface,furniture, or any other surface that could be marred by exposure toheat since the computer

3. Plug the power cord into a live wall outlet - the Battery and DC INindicators on the front of the computer should glow.Opening the displayThe displ

Turning on the powerThis section describes how to turn on the power - the Power indicator willthen indicate the status. Please refer to the Monitoring

Starting up for the first timeThe Windows 7 Startup Screen will be the first screen displayed when youturn on the power. Follow the on-screen instruct

When you have to turn off your computer aboard an aircraft or in placeswhere electronic devices are regulated or controlled, always completelyshut dow

Executing Sleep ModeYou can also enable Sleep Mode by pressing FN + F3 - please refer to theHot key functions section in Chapter 3, Operating Basics,

Benefits of Hibernation ModeThe Hibernation Mode feature provides the following benefits:Saves data to the hard disk drive when the computer automatic

Restarting the computerCertain conditions require that you reset the computer, for example if:You change certain computer settings.An error occurs and

Chapter 2The Grand TourThis chapter identifies the various components of the computer - it isrecommended that you become familiar with each before you

Video mode ... 3-51Computer Handling ...

Figure 2-1 Front of the computer with display panel closed (R850)13245671. DC IN indicator 5. Memory media slot indicator2. Power indicator 6. Wireles

Wireless communica-tion indicatorThe Wireless communication indicator glowsorange when the Wireless functions are turnedon.Some models are equipped wi

Do not block the cooling vents. Keep foreign metal objects, such asscrews, staples and paper clips, out of the cooling vents. Foreign metalobjects can

ExpressCard slot This slot allows you to install a singleExpressCard/34 device.Some models are equipped with a ExpressCardslot.Smart Card slot This sl

eSATA/USB comboportOne eSATA/USB combo port, which complies tothe USB 2.0 standard, is provided on the rightside of the computer. This port has eSATA(

Figure 2-4 The back of the computer (R850)11. Battery pack Battery pack The rechargeable lithium-ion battery packprovides power to the computer when t

Battery lock Slide the battery lock to release the battery packready for removal.Battery release latch Slide and hold this latch into its "Unlock

Figure 2-6 The front of the computer with the display panel open (R850)2611 121293516141678181310151741. Display screen 10. Touch Pad ON/OFF button2.

Web Camera LED The Web Camera LED glows when the WebCamera is operating.Web Camera Web Camera is a device that allows you torecord video or take photo

eco button Press this button to launch the TOSHBIA ecoUtility. TOSHIBA eco Utility can be used only inWindows® 7.TOSHIBA Presenta-tion buttonThe TOSHI

Copyright© 2011 by TOSHIBA Corporation. All rights reserved. Under the copyrightlaws, this manual cannot be reproduced in any form without the priorwr

Display hinges The display hinges allow the display panel to beposition at a variety of easy-to-view angles.LCD Sensor switch This switch senses when

Power indicator The Power indicator normally glows green whenthe computer is turned on. However, if you turnthe computer off into Sleep Mode, this ind

Figure 2-8 The left side of the computer (R840)786541 2 31. DC IN 19V jack 5. eSATA/USB combo port2. Cooling vents 6. Universal Serial Bus (USB 2.0) p

eSATA/USB comboportOne eSATA/USB combo port, which complies tothe USB 2.0 standard, is provided on the left sideof the computer. This port has eSATA (

2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.ExpressCard slot This slot allows you to install a singleExpressCard/34 device.Some mo

Please note that it is not possible to confirm the operation of all functions ofall USB devices that are available. In view of this it may be noted th

Figure 2-11 The underside of the computer (R840)152 4631. Battery lock 4. Battery release latch2. Docking port* 5. Memory module slot3. Battery Pack 6

Memory module slot The memory module slot allows for theinstallation, replacement and removal ofadditional memory module.1 GB, 2 GB or 4 GB memory mod

Figure 2-12 The front of the computer with the display panel open (R840)3 481217 16161413218910764571115181. Display screen 10. Keyboard2. Microphone*

Microphone A built-in microphone allows you to import andrecord sounds for your application - please referto the Sound System section in Chapter 3,Ope

Memory Stick, Memory Stick Duo, Memory Stick PRO, Memory Stick PRODuo and Memory Stick Micro are trademarks or registered trademarks ofSony Corporatio

LCD Sensor switch This switch senses when the display panel iseither closed or opened and activates the PanelPower Off/On feature as appropriate. Fore

AccuPoint A pointer control device located in the center ofthe keyboard is used to control the on-screenpointer. Refer to the Using the AccuPoint sect

DC IN indicator The DC IN indicator normally glows green whenpower is being correctly supplied from the ACpower adaptor. However, If the output voltag

Left side (R830)The following figures show the computer’s left side.Figure 2-14 The left side of the computer (R830)1 2 3 4 651. DC IN 19V jack 4. eSA

Universal Serial Bus(USB 2.0) portOne Universal Serial Bus port, which complies tothe USB 2.0 standard, is provided on the left sideof the computer.HD

The integrated sound system provides support for the computer's internalspeakers and microphone, as allowing an external microphone andheadphones

Please note that it is not possible to confirm the operation of all functions ofall USB devices that are available. In view of this it may be noted th

Figure 2-17 The underside of the computer (R830)1 2 43561. Battery lock 4. Battery release latch2. Docking port* 5. Memory module slot3. Battery Pack

Memory module slot The memory module slot allows for theinstallation, replacement and removal ofadditional memory module.1 GB, 2 GB or 4 GB memory mod

Figure 2-18 The front of the computer with the display panel open (R830)131112121021171615365784141891. Display screen 10. Touch Pad ON/OFF button2. W

2. This device must accept any interference received, includinginterference that may cause undesired operation.ContactAddress: TOSHIBA America Informa

Web Camera Web Camera is a device that allows you torecord video or take photographs with yourcomputer. You can use it for video chatting orvideo conf

eco button Press this button to launch the TOSHIBA ecoUtility. TOSHIBA eco Utility can be used only inWindows® 7.Microphone A built-in microphone allo

LCD Sensor switch This switch senses when the display panel iseither closed or opened and activates the PanelPower Off/On feature as appropriate. Fore

SSD is a large-capacity storage media which uses Solid-StateMemory in place of a magnetic disk of the hard disk.Under certain unusual conditions of pr

Graphics controller The graphics controller maximizes displayperformance.Legal Footnote (Graphics Processing Unit ("GPU"))For more informati

The Display Power Saving Technology feature is enabled at factory default.If you want to disable this feature, you can disable it.The Display Power Sa

Chapter 3Operating BasicsThis chapter describes the basic operations of your computer, highlightsthe precautions that should be taken when using it.TO

Two buttons above the Touch Pad work in the same way with theAccuPoint as they do with the Touch Pad. Refer to the Using the TouchPad section for deta

The number of keys available on your keyboard will depend on whichcountry/region your computer is configured for, with keyboards beingavailable for nu

the FN key, those keys marked with icons also execute specific functionson the computer.Soft keys: FN key combinationsThe FN (function) is used in com

product in working environments other than the above mentioned“Residential, commercial and light industry environments”.For example, the following env

2. Select the desired option.The selected Card is displayed full-size with its available optionsbelow it. All other Cards are again hidden from view.3

If no wireless communication device is installed, no dialog box will appear.Touch PadPressing FN + F9 enables or disables the Touch Pad function.ZoomP

their front edge. The overlay provides the same function as the numerickeypad on a standard 104/105-key enhanced keyboard.Turning on the overlaysThe n

Generating ASCII charactersNot all ASCII characters can be generated using normal keyboardoperation, but you are able to generate these characters usi

Figure 3-6 Swipe the finger111. SensorAvoid swiping with your finger stiff or pressed too hard onto thesensor, and take care to ensure that the center

Clean the sensor with a lint-free cloth - do not use detergent or anyother chemicals to clean the sensor.Avoid the following finger conditions for enr

Fingerprint utility limitationsTOSHIBA does not guarantee that the fingerprint utility technology will becompletely secure or error-free, or that it w

It is strongly recommended that you register 2 or more fingerprints.You cannot enroll the same fingerprint more than once, even on adifferent user acc

Windows Logon via Fingerprint AuthenticationIn place of the usual Windows logon by ID and password, fingerprintauthentication also allows logon to Win

Overview about Fingerprint Single Sign-on featureThis is a feature that allows the user to complete the authentication for boththe User/BIOS Password

LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM.Canadian regulatory information (Canada only)This digital apparatus does not

Optical disc drivesThe computer may be installed with an Optical Disc Drive. When thecomputer is accessing an optical disc, an indicator on the drive

2. Grasp the disc tray gently and pull until it is fully opened.Figure 3-7 Pressing the eject button and pulling the disc tray open (R830)121. Disc tr

3. Lay the disc, label side up, in the disc tray.Figure 3-8 Inserting a disc (R830)11. Laser lensWhen the disc tray is fully opened, the edge of the c

Do not press the eject button while the computer is accessing the mediadrive. Wait for the optical disc drive indicator to go out before you open thed

Writable discsThis section describes the types of writable discs. Check the specificationsof your drive to see the types of discs it can write. Use TO

Any change or loss of the recorded contents of media that may becaused by writing or rewriting with this product, or for any businessprofit loss or bu

DVD-RW:DVD Specifications for Recordable Disc for Version 1.1 or version1.2Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media)MITSUBIS

If the media is of poor quality, or is dirty or damaged, writing orrewriting errors may occur.Set the computer on a level surface and avoid places sub

When you back up a DVD disc, be sure that the source drive supportsrecording to DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL orDVD+RW media - if this is n

Use DVD-Video discs with a region code which is either "the same asthe factory default setting" (if applicable) or "ALL".Do not pl

The crossed out wheeled dust bin symbol indicates thatproducts must be collected and disposed of separatelyfrom household waste. Integrated batteries

If the DVD-Video image is not displayed on an external display ortelevision, stop the TOSHIBA VIDEO PLAYER, and change thescreen resolution. To change

Only some models are equipped with both Wireless LAN and Bluetoothfunctions.Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near amic

Setting1. Please make sure that the Wireless Communication function is on.2. Click Start -> Control Panel -> Network and Internet -> Network

The range of the wireless signal is related to the transmit rate of thewireless communication. Communications at lower transmit range maytravel larger

This Bluetooth Stack is based on the Bluetooth Version 1.1/1.2/2.0+EDR/2.1+EDR/3.0/3.0+HS specification, depending on the model youpurchased. However,

LAN cable typesThe computer must be configured properly before connecting to a LAN.Logging onto a LAN using the computer’s default settings could caus

3. Plug the other end of the cable into a LAN hub connector or router.Check with your LAN administrator and hardware or software vendorbefore using or

2. Grasp the Dummy card and draw it.3. Insert the ExpressCard into the ExpressCard slot on the hand side ofthe computer.4. Press the ExpressCard gentl

Your computer supports ISO7816-3 asynchronous cards (supportprotocols are T=0 and T=1) with a working voltage of 5V.Inserting a Smart CardThe Smart Ca

Memory media slotThe computer is equipped with a memory media slot that canaccommodate some kinds of memory media with various memorycapacities so tha