Toshiba SD-K530SU User Manual Page 12

  • Download
  • Add to my manuals
  • Print
  • Page
    / 47
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 11
12
Connections (Continued)
Basic TV Connections
Make one of the following connections, depending on
the capabilities of your existing equipment.
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to the
antenna in jack on the TV using the 75-ohm Coaxial
Cable supplied (R).
Note
If you use this connection, tune the TV to the
DVD+VCR’s RF output channel (CH 3 or 4).
How to set the DVD+VCR’s RF output channel
1. When the DVD+VCR is turned off,
press and hold
REW m or FWD M on the front panel for about
five seconds.
It will turn itself on and “RF03” or “RF04” appears in the dis-
play window.
2.
Press REW m or FWD M on the front panel or
CH/TRK (+/-) on the remote control to change the RF
output channel (CH 03 or CH 04).
3.
Turn off and on the DVD+VCR.
4.
Press the TV CH to 3 or 4 depending on the RF
output channel you had selected.
Now you can watch the DVD+VCR playback on CH3
or CH4 of your TV.
Audio/Video connection
11
Connect the DVD/VCR VIDEO OUT jack on the
DVD+VCR to the video in jack on the TV using the
video cable supplied (V).
22
Connect the Left and Right DVD/VCR AUDIO OUT
jacks on the DVD+VCR to the audio left/right in
jacks on the TV (A1) using the supplied audio
cables.
Note
If you use this connection, set the TV’s source selector
to VIDEO.
Optional, Preferred TV Connections
Note
You can ONLY watch and listen to DVD playback
through the connections shown below.
S-Video connection
11
Connect the S-VIDEO OUT jack on the DVD+VCR
to the S-Video in jack on the TV using the optional
S-Video cable (S).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD+VCR to the audio left/right in jacks on the
TV using the supplied audio cables (A2).
Component Video (Color Stream
®
) / Progressive
Scan (ColorStream
®
pro) connection
If your television is a high-definition or “digital ready”
television, you may take advantage of the
DVD+VCR’s progressive scan output for the highest
video resolution possible.
If your TV does not accept the Progressive Scan for-
mat, the picture will appear scrambled if you try
Progressive Scan on the DVD+VCR.
11
Connect the COMPONENT / PROGRESSIVE
SCAN VIDEO OUT jacks on the DVD+VCR to the
corresponding in jacks on the TV using an optional
Y Pb Pr cable (C).
22
Connect the Left and Right AUDIO OUT jacks of
the DVD+VCR to the audio left/right in jacks on the
TV (A2) using the supplied audio cables.
Notes
Set the Progressive Scan to “On” on the setup menu
for progressive scan signal, see page 18.
When you use Component Video signal, set the
Progressive Scan to “Off” on the setup menu.
Progressive scan does not work with the analog video
connections (yellow VIDEO OUT jack and S-VIDEO
OUT jack).
L
R
AUDIO INPUT
VIDEO
INPUT
ANTENNA
INPUT
Rear of TV
Rear of DVD+VCR
A1 VR
Y
Pb
Pr
COMPONENT VIDEO INPUT
L
R
AUDIO INPUT
S-VIDEO
INPUT
Rear of TV
Rear of DVD+VCR
S
A2
C
Page view 11
1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 46 47

Comments to this Manuals

No comments