Toshiba B-570 SERIES User Manual Page 1

TEC Thermal PrinterB-570 SERIESOriginal Nov., 1993(Revision Mar., 2000)Document No. EM0-33013APRINTED IN JAPANTABLE OF CONTENTSOWNER'S MANUAL ...

1-11. INTRODUCTIONEM1-330351.1 Applicable Model1. INTRODUCTIONThank you for choosing the TEC B-570 series thermal/transfer printer. This new generati

6-10EM18-33010A6. DIAG. TEST OPERATIONSensor/SwitchHead up switchCutter home positionswitchRewind full sensorSlit sensor #1 (ribbonrewind)Slit sensor

6-11EM18-33010A6. DIAG. TEST OPERATIONDIP SWDIP Switch 10: OFF (OPEN)1: ON (SHORT)DIP Switch 20: OFF (OPEN)1: ON (SHORT)Pin No.000000008765432

6-12EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. If the head broken element check results in ‘HEAD ERROR’, the print head must bereplaced after referri

6-13EM18-33010A6. DIAG. TEST OPERATION6.3 PARAMETER SETTING MODEThe following items are set in the parameter setting mode. The values set in this mod

6-14EM18-33010A6. DIAG. TEST OPERATION Parameter Setting Mode Table(Revision Date: Dec. 10 ‘99)6.3 PARAMETER SETTING MODEMode NameFEED ADJUSTCUT ADJU

6-15EM18-33010A6. DIAG. TEST OPERATION [FEED] key: Pressing the [FEED] key one timeis a -0.5 mm change, up to -50.0mm. (See NOTE 2.) [RESTART] key:

6-16EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa fast forward.2. Max. f

6-17EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa fast forward.2. Max. f

6-18EM18-33010A6. DIAG. TEST OPERATION6.3 PARAMETER SETTING MODE Feed Length Fine Adjustment Example Cut Position Fine Adjustment ExampleAAAAAAAAAAA

6-19EM18-33010A6. DIAG. TEST OPERATION1 Idling2 Printing the first label A is completed.3 Label A is fed to the cut position and the front gap is cut.

2-12. SPECIFICATIONSEM1-330352.1 Printer2. SPECIFICATIONS2.1 PrinterSupply voltagePower consumptionOperating temperature rangeRelative humidityPrint h

6-20EM18-33010A6. DIAG. TEST OPERATIONNOTE: The print stop position when printing the label in strip mode varies according to label lengthas the strip

6-21EM18-33010A6. DIAG. TEST OPERATION6.3 PARAMETER SETTING MODE Back Feed Length Fine Adjustment ExampleAAAAAAAAAAAA+ 0.0 mmFeed Direction+3.0 mm-3.

6-22EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa fast forward.2. Max. f

6-23EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. The X axis fine adjustment is performed to fine adjust the X axis of the drawing in theleft or right d

6-24EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1 Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa fast forward.2. A chang

6-25EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa fast forward.2. A chan

6-26EM18-33010A6. DIAG. TEST OPERATION• 0 (without slash)• ø (with slash)NOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seco

6-27EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa fast forward.2. A chan

6-28EM18-33010A6. DIAG. TEST OPERATIONSVO8A1002 : Jan. 19, '986.3 PARAMETER SETTING MODECO E MANUALDCO TLOL CODE1 1BNCO TROL CODE2

6-29EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa fast forward.2. Non-tr

2-22. SPECIFICATIONSEM1-330352.3 MediaTypeWidthLengthOuter diameterSpool type68 mm ~ 134 mm600 mø90 mm (max.)2.4 RibbonNOTES: 1. "On the fly issu

6-30EM18-33010A6. DIAG. TEST OPERATION6.3.10 Ribbon Motor Drive Voltage Fine AdjustmentNOTES: 1. Holding the [FEED] key or [RESTART] key down for more

6-31EM18-33010A6. DIAG. TEST OPERATION6.3.11 Strip Wait Status SettingNOTE: When the status type 1 is selected, the printer will send (00H) in respons

6-32EM18-33010A6. DIAG. TEST OPERATION6.3.12 Stacker SelectionNOTE: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enablesa

6-33EM18-33010A6. DIAG. TEST OPERATION6.3.13 Threshold Manual Fine Adjustment for the Black Mark SensorNOTES: 1. Holding the [FEED] key or [RESTART] k

6-34EM18-33010A6. DIAG. TEST OPERATION6.3.14 Threshold Manual Fine Adjustment for the Feed Gap SensorNOTES: 1. Holding the [FEED] key or [RESTART] key

6-35EM18-33010A6. DIAG. TEST OPERATION(Revision Date: Jan. 14 ‘99)6.3 PARAMETER SETTING MODE How To Calculate Theshold Fine Adjustment ValueIf the fo

6-36EM18-33010A6. DIAG. TEST OPERATION(Revision Date: Jan. 14 ‘99)6.3 PARAMETER SETTING MODENOTE: The following operation cannot be performed unless t

6-37EM18-33010A6. DIAG. TEST OPERATION(Revision Date: Jan. 14 ‘99)6.3 PARAMETER SETTING MODE6.3.15 Kanji Code SelectionNOTES: 1. Holding the [FEED] ke

6-38EM18-33010A6. DIAG. TEST OPERATION(Revision Date: Aug. 5 ‘99)6.3 PARAMETER SETTING MODE6.3.16 Euro Font Code SelectionNOTES: 1. Holding the [FEED]

6-396.3.17 Transmission Control Mode SelectionNOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enable.2. A changed Tra

3-13. OVERVIEWEM1-330353.1 Front/Rear View3. OVERVIEW3.1 Front/Rear View3.2 Operation PanelMESSAGE DISPLAY (LCD)Displays messages in the language sele

6-40EM18-33010A6. DIAG. TEST OPERATION(Revision Date: Dec. 10 ‘99)6.3 PARAMETER SETTING MODE6.3.18 Reset Selection when the INPUT • PRIME Signal is ON

6-41EM18-33010A6. DIAG. TEST OPERATION(Revision Date Feb. 07, ’97)6.4 TEST PRINT MODE6.4 TEST PRINT MODETest print mode contains normal test print and

6-42EM18-33010A6. DIAG. TEST OPERATION6.4 TEST PRINT MODESet the print speedSet the print count from those at theright by pressing the [FEED] key or

6-43EM18-33010A6. DIAG. TEST OPERATION6.4 TEST PRINT MODESet the issue mode typePress [PAUSE] key. (See NOTE 3.)Press the [PAUSE] key. (See NOTE 3.)Pr

6-44EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. When there is no change to the print condition, select one of the test print options to issue the test

6-45EM18-33010A6. DIAG. TEST OPERATION(Revision Date Feb. 07, ’97)6.4 TEST PRINT MODE9. When the transmissive ribbon is selected and DIP SW. 1-1 is s

6-46EM18-33010A6. DIAG. TEST OPERATION6.4.2 Process Test PrintIn the process test print, the test print is automatically performed on the following co

6-47EM18-33010A6. DIAG. TEST OPERATIONAU O PRINT(REFLECT.)T<3 TEST PRINT><3 TEST PRINT>AU O PRINT(TRANS.)TAU O PRINT(TRANS.)TAU O PRINT(TR

6-48EM18-33010A6. DIAG. TEST OPERATIONNOTE: Since the thermistor is supervised every 200 ms while displaying the status, the displaycould vary. (Revis

6-49EM18-33010A6. DIAG. TEST OPERATIONPower offTurn on the power whileholding down the [FEED]key and [PAUSE] key.Press the [FEED] key three times.Set

4-14. DIP SWITCH FUNCTIONSEM1-330354. DIP SWITCH FUNCTIONSWARNING:Turn the POWER OFF before switching the functions.Fig. 4-14. DIP SWITCH FUNCTIONSThe

6-50EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Make sure to adjust the feed gap sensor using the backing paper with no label as acriterion. Though a

6-51EM18-33010A6. DIAG. TEST OPERATIONNOTE: Pressing the [PAUSE] key validates the sensor setting. The value of the sensor isdisplayed up to 5.0 V.6.

6-52EM18-33010A6. DIAG. TEST OPERATIONNOTE: Pressing the [PAUSE] key validates the sensor setting. The value of the sensor isdisplayed up to 5.0 V.6.

6-53EM18-33010A6. DIAG. TEST OPERATIONFunctionIf you enter the RAM clear mode by mistake, specify this mode toescape from the RAM clear mode without e

6-54EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Total media distance covered (TL FEED) and the adjustment value for the sensors cannotbe cleared.2. Da

6-55EM18-33010A6. DIAG. TEST OPERATION6.6. RAM CLEAR MODENOTE: Confirm that “COMPLETE” is displayed, then turn the power off.6.6.1 Maintenance Counter

6-56EM18-33010A6. DIAG. TEST OPERATIONNOTE: Confirm that “COMPLETE” is displayed, then turn the power off.6.6 RAM CLEAR MODE6.6.2 Parameter ClearPower

7-1EM18-33010A7. PROGRAM DOWN LOAD(Revision Date: Feb. 10, 2000)7.1 DOS VERSION7. PROGRAM DOWN LOAD7.1 DOS VERSIONThe main program for the printer has

7-2EM18-33010A7. PROGRAM DOWN LOAD↵7.1.3 DOWN LOAD PROCEDURE(1) Turn the PC power on.(2) Turn the printer power on.(3) Insert the program down load fl

7-3EM18-33010A7. PROGRAM DOWN LOAD(Revision Date: Feb. 10, 2000)7.1 DOS VERSIONBErrorcodeCheck the following when an error occurs:• The printer power

5-15. INSTALLING THE PRINTEREM1-330355.1 INSTALLING THE PRINTERWARNING!Turn the POWER SWITCH to OFF before connecting the power cord or cables.Fig. 5-

7-4EM18-33010A7. PROGRAM DOWN LOAD(Revision Date: Feb. 10, 2000)7.2 WINDOWS VERSION7.2 WINDOWS VERSIONThe main program for the printer has been writte

7-5EM18-33010A7. PROGRAM DOWN LOAD(Revision Date: Feb. 10, 2000)7.2 WINDOWS VERSION7.2.2 Setup and System requirementsConnect the B-570 printer to the

7-6EM18-33010A7. PROGRAM DOWN LOAD7.2.3 Installation Procedure of Down Load Program(1) Start up Windows 95 or Windows 98, and then insert the Program

7-7EM18-33010A7. PROGRAM DOWN LOAD(Revision Date: Feb. 10, 2000)7.2 WINDOWS VERSION7.2.4 Installation Procedure of Firmware(1) Before performing the p

7-8EM18-33010A7. PROGRAM DOWN LOAD(Revision Date: Feb. 10, 2000)7.2 WINDOWS VERSION(6) From the File (F) drop down menu, select Open (O).(7) The file

7-9EM18-33010A7. PROGRAM DOWN LOAD(9) The display restores to the Download Program for B-X. Make sure of the Download file.(Revision Date: Feb. 10, 2

7-10EM18-33010A7. PROGRAM DOWN LOAD(13) When the program has been successfully downloaded, the following message will appear.If an error occurs during

PRINTED IN JAPANEM18-33010A

6-16. LOADING THE MEDIAEM1-33035Fig. 6-1NOTES: 1.When the head lever is turned to position 2, the print head is raised.2.When the head lever is turned

6-26. LOADING THE MEDIAEM1-330356. LOADING THE MEDIA4. Put the media on the supply shaft.5. Pass the media around the damper, then pull the media towa

6-36. LOADING THE MEDIAEM1-330356. LOADING THE MEDIA Removing the paper holders' upper plates from the media guide1 Remove the two T-4x8 screws

6-46. LOADING THE MEDIAEM1-330356. LOADING THE MEDIA An easy way to set the black mark sensor position1 Pull the media about 500 mm out of the front

PrecautionThis service manual, intended for field engineers and technicians, is designed as a guide formaintenance, service and repair of TOSHIBA TEC

6-56. LOADING THE MEDIAEM1-330356. LOADING THE MEDIA10. The media is now loaded and the sensor position is set.Batch type:NOTE: Set the selection swit

6-66. LOADING THE MEDIAEM1-330356. LOADING THE MEDIACutter type: Where a cutter is fitted load the media as standard and feed it through the cutter mo

7-17. LOADING THE RIBBONEM1-33035Fig. 7-24. Reset the ribbon shaft holder plate by aligning it with the ribbon shaft.5. Turn the head lever clockwise

8-18. INSERTING THE OPTIONAL FLASH MEMORY CARDEM1-330358. INSERTING THE OPTIONAL FLASH MEMORY CARD8. INSERTING THE OPTIONAL FLASH MEMORY CARD1. Turn t

9-19. CARE/HANDLING OF THE MEDIA AND RIBBONEM1-330359. CARE/HANDLING OF THE MEDIA AND RIBBONCAUTION:Be sure to read carefully and understand the Suppl

10-110. GENERAL MAINTENANCEEM1-33035Fig. 10-110.1 CleaningWARNING!1. Be careful when handling the print head as it becomes very hot.2. Care must be ta

10-210. GENERAL MAINTENANCEEM1-3303510.2 Covers and Panels10.2 Covers and PanelsThe covers should be cleaned by wiping with a dry cloth or a cloth sl

10-310. GENERAL MAINTENANCEEM1-33035 Cleaning the Cutter Unit10.3 Removing Jammed PaperWARNING!1. Be sure to turn the power off before cleaning the c

10-410. GENERAL MAINTENANCEEM1-3303510.4 Threshold Setting10.4 Threshold SettingFor the printer to maintain a constant print position it uses the tran

10-510. GENERAL MAINTENANCE10.5 Auto Ribbon Saving ModeAuto ribbon saving function is activated when it is selected by DIP switch (Refer to page 4-1)

11-111. TROUBLESHOOTINGEM1-3303511. TROUBLESHOOTING11. TROUBLESHOOTINGPAPER JAM****HEAD OPEN****NO PAPER****NO RIBBON****REWIND FULL****1. The media i

11-211. TROUBLESHOOTINGEM1-33035Error MessageProblem Solution11. TROUBLESHOOTINGTurn the power off and decrease theprint head temperature.1. Restart t

11-311. TROUBLESHOOTINGEM1-3303511. TROUBLESHOOTINGNo print.Dots missing in the print.Unclear (or blurred) printing.Power does not come on.Printer doe

PRINTED IN JAPANEM1-33035E

TEC Thermal PrinterB-570 SERIESOriginal Nov., 1993(Revised Feb., 2000)PRINTED IN JAPANProduct DescriptionDocument No. EM10-33006ATable of Contents

TABLE OF CONTENTS1. OUTLINE OF THE SYSTEM ... 1- 11.1 FEATURES OF THE B-570

1-11. OUTLINE OF THE SYSTEMEM10-33006A1. OUTLINE OF THE SYSTEM1.1 FEATURES OF THE B-570 SERIES1) Various bar codes, characters and graphic data can be

1-21. OUTLINE OF THE SYSTEMEM10-33006A1.3 OVERVIEW AND DIMENSIONS (APPROXIMATE)POWERON LINEERROR FEED RESTART PAUSE1.3 OVERVIEW AND DIMENSIONS (APP

1-31. OUTLINE OF THE SYSTEMEM10-33006A(Revision Date: Feb. 10. 2000)1.4 BASIC SPECIFICATIONSeludoM/stoDedocraB2345678E/A-CPU31/8NAE31/8NAJ)mm(htdiWelu

PRINTED IN JAPANEO0-33004

1-41. OUTLINE OF THE SYSTEMEM10-33006A NW-7/CODE39/ITF/MSI/Industrial 2 of 5 ...The width of narrow bars, wide bars and spacescan be optionally ch

1-51. OUTLINE OF THE SYSTEMEM10-33006A3 Auto cut mechanismWhen the cutter module is installed, the backing paper and tag paper are cut individually (

1-61. OUTLINE OF THE SYSTEMEM10-33006A1.5 ELECTORONICS SPECIFICATIONS(5) Error detection Parity check: VRC (Vertical parity check) Framing error: Th

1-71. OUTLINE OF THE SYSTEMEM10-33006A READY/BUSY (RTS) Protocol• When initialized after power on, this printer becomes ready to receive data and con

1-81. OUTLINE OF THE SYSTEMEM10-33006A(Revision Date: Aug. 5 '99)1.5 ELECTRONICS SPECIFICATIONSSN75189 or equivalent RDCTSDSRTDRTSDTRSN75188 o

1-91. OUTLINE OF THE SYSTEMEM10-33006ASignal NameDATA 1 ~ 8INPUT•PRIMEDATA•STBBUSYFAULTPAUSEACKPE2 Centronics interface(1) Data input method: 8-bit pa

1-101. OUTLINE OF THE SYSTEMEM10-33006A1.5 ELECTRONICS SPECIFICATIONSExternal controller, etc. (In case of photo-coupler)~~PrinterOUT0OUT5COM2Vcc Ou

1-111. OUTLINE OF THE SYSTEMEM10-33006A1.5 ELECTRONICS SPECIFICATIONS Feed gap sensor (Transmissive sensor)This sensor detects the difference in pote

1-121. OUTLINE OF THE SYSTEMEM10-33006A1.5 ELECTRONICS SPECIFICATIONS5 Rewind full sensor (Transmissive sensor)This sensor detects excessive winding w

2-12. SUPPLY SPECIFICATIONSEM10-33006ATag Paper50.8 ~ 140.00.15 ~ 0.29200.0 max.I-BEST S / I-BEST WThermal Label50.8 ~ 140.00.13 ~ 0.17200.0 max.RICOH

TEC Thermal PrinterB-570-QQ SERIESOwner’s ManualTable of Contents

2-22. SUPPLY SPECIFICATIONSEM10-33006A2) Tag Paper<Design>NOTE: The reflection rate of the black mark is 10% or less at wavelength of 950 nm. A

2-32. SUPPLY SPECIFICATIONSEM10-33006A2.2 RIBBON(Revision Date Sep. 25, '95)2.2 RIBBON68 ~ 134 mm25.7 ± 0.2 mmFig. 2-7NOTE: When purchasing ribb

2-42. SUPPLY SPECIFICATIONSEM10-33006A(Revision Date Aug. 10, '95)2.2 RIBBON2.3 CARE AND HANDLING OF THE MEDIA AND RIBBONCAUTION:Be sure to read

3-13. OPTIONAL KITEM10-33006A3. OPTIONAL KIT3.1 CUTTER MODULE: B-4205-QMThis compact cutter module uses a built-in swing cutter. The specification is

3-23. OPTIONAL KITEM10-33006A3.2 HIGH SPEED PC INTERFACE BOARD: B-4800-PC-QMCommand transfer and printing can be processed quickly by connecting a PC

3-33. OPTIONAL KITEM10-33006A3.3 MEMORY MODULEThis memory module is a D-RAM PC board used to extend the image buffer. An image buffer, equippedwith 2

PRINTED IN JAPANEM10-33006A

TEC Thermal PrinterB-570 SERIESOriginal Nov., 1993(Revision Feb., 2000)PRINTED IN JAPANMaintenance ManualDocument No. EM18-33010ATable of Contents

This equipment has been tested and found to comply with the limits for a Class A digital device,pursuant to Part 15 of the FCC Rules. These limits ar

EM18-33010ATABLE OF CONTENTS1. UNPACKING ... 1- 11.

1-1EM18-33010A1. UNPACKING1.2 CHECKS1) Check for any damage or scratches on the machine.2) Confirm that none of the accessories are missing.NOTE: Keep

2-1EM18-33010A2. MAJOR UNIT REPLACEMENTCAUTION: 1) Lubrication: During parts replacement2) Kinds of oil: FLOIL G-488: 1 Kg can. (Part No. 1945490600

2-2EM18-33010A2. MAJOR UNIT REPLACEMENT3) Disconnect the 13 connectors from the CPU PC board.4) Remove the six screws (SM-3x6B, SM-3x6C) to detach the

2-3EM18-33010A2. MAJOR UNIT REPLACEMENTCAUTION:Be careful when replacing the CPU PC board, since a non-resettable counter (IC12) is installed onthis b

2-4EM18-33010A2. MAJOR UNIT REPLACEMENT4) When replacing the stepping motor, place the platen belt first then the feed roller belt around thepinion ge

2-5EM18-33010A2. MAJOR UNIT REPLACEMENT2) Replace the ribbon motors, then align the dowels to attach the ribbon motors. Reassemble in thereverse orde

2-6EM18-33010A2. MAJOR UNIT REPLACEMENTFig. 2-102.5 REPLACING THE SOLENOID2.5 REPLACING THE SOLENOIDNOTE: The following procedure can be employed with

2-7EM18-33010A2. MAJOR UNIT REPLACEMENT2.5 REPLACING THE SOLENOIDNOTE: Make sure to remove any dust that appears during removal or installation becaus

2-8EM18-33010A2. MAJOR UNIT REPLACEMENTFig. 2-13(Revision Date Feb. 01, ’96)2.6 REPLACING THE PRINT HEAD2.6 REPLACING THE PRINT HEADCAUTION:1. NEVER t

(i)Safety SummaryEM1-33035Safety SummaryPersonal safety in handling or maintaining the equipment is extremely important. Warnings and Cautionsnecessa

2-9EM18-33010A2. MAJOR UNIT REPLACEMENTStrip ShaftFig. 2-14(Revision Date Feb. 01, ’96)2.6 REPLACING THE PRINT HEAD Adjusting the print head position

2-10EM18-33010A2. MAJOR UNIT REPLACEMENTFig. 2-152.6.2 New type print head1) Turn the head lever clockwise to lower the print head. Remove the two SM

2-11EM18-33010A2. MAJOR UNIT REPLACEMENTFig. 2-172.6 REPLACING THE PRINT HEAD2.7 REPLACING THE PLATEN AND FEED ROLLER1) Remove the front plate and bel

2-12EM18-33010A2. MAJOR UNIT REPLACEMENT3) Disconnect the connector for the strip sensor (LED).4) Remove the six screws (FL-4x6, B-4x12 and P-3x12) to

2-13EM18-33010A2. MAJOR UNIT REPLACEMENT5) Replace the paper sensor and reassemble in the reverse order of removal.6) After replacing the paper sensor

2-14EM18-33010A2. MAJOR UNIT REPLACEMENT(Revision Date Sep. 29, ’95)2.10 REPLACING THE PINCH ROLLER SHAFT ASS’Y2.10 REPLACING THE PINCH ROLLER SHAFT A

2-15EM18-33010A2. MAJOR UNIT REPLACEMENT(Revision Date Sep. 29, ’95)2.10 REPLACING THE PINCH ROLLER SHAFT ASS’Y Adjustment1. Install the pinch roller

2-16EM18-33010A2. MAJOR UNIT REPLACEMENTFig. 2-27(Revision Date Sep. 29, ’95)2.10 REPLACING THE PINCH ROLLER SHAFT ASS’Y2.11CORRECTING SKEW PRINTINGl

3-1EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENT3. INSTALLATION PROCEDURE FOR THE OPTIONALEQUIPMENT(Revision Date: Feb. 10, 2000)3.1

3-2EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENT9. Reassemble in the reverse order of removal.10. Following procedure should be empl

(ii)Safety SummaryEM1-33035CAUTIONThis indicates that there is the risk of personal Injury or damage toobjects if the machines are improperly handled

3-3EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENT5. Unclamp and disconnect the connector for the strip sensor from CN6 on the CPU PC

3-4EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENTFig. 3-5Fig. 3-63.2 CUTTER MODULE (B-4205-QM)7. Install the cutter unit with the att

3-5EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENTFig. 3-8(Revision Date Aug. 11, ’95)3.2 CUTTER MODULE (B-4205-QM) Adjusting the Cut

3-6EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENTMax. drawing size (on-the-fly)(W)x(H) (mm)138.0 x 149.3138.0 x 234.6138.0 x 320.0138

3-7EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENT(Revision Date: Feb. 10, 2000)3.3 MEMORY MODULE3.3.2 For New CPU PC Board1. Open the

3-8EM18-33010A3. INSTALLATION PROCEDURE FOR THE OPTIONAL EQUIPMENT3. Remove the FL-4x5 screw to detach the blind plate on the back of the printer and

4-1EM18-33010A4. MECHANISM DESCRIPTIONAfter making a cut, the arm turns the micro switch off and the cutter home position is detected.When the cutter

4-2EM18-33010A4. MECHANISM DESCRIPTION(Revision Date: Feb. 10, 2000)4.2 HARNESS WIRING4.2 HARNESS WIRINGFig. 4-3Rewind Full SensorStrip SensorDC Moto

5-15. TROUBLESHOOTINGEM18-33010A5. TROUBLESHOOTING• Replace the power cable or powerinlet.• Replace the PS unit.• Replace the power harness.• Replace

5-25. TROUBLESHOOTINGEM18-33010A5. TROUBLESHOOTING• Replace the print head.• Replace the print head harness.• Replace the CPU PC board.• Use only TOSH

EM1-33035CAUTION:1. This manual may not be copied in whole or in part without prior written permission ofTOSHIBA TEC.2. The contents of this manual ma

PageEM18-33010A(Revision Date: Dec. 10 '99)CAUTION:1. This manual may not be copied in whole or in part without prior written permission ofTOSHIB

6-1EM18-33010A6. DIAG. TEST OPERATION6. DIAG. TEST OPERATION6.1 OUTLINE OF THE DIAG. TEST OPERATIONIn system mode the diag. test operation is used to

6-2EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. Pressing the [PAUSE] key during printing causes the printer to pause printing and showthe number of rem

6-3EM18-33010A6. DIAG. TEST OPERATION(Revision Date Jan. 14, ’99)6.2 SELF TEST MODE6.2 SELF TEST MODEIn self test mode the printer status is printed i

6-4EM18-33010A6. DIAG. TEST OPERATION#(1)(2)(3)(4)(5)(6)(7)(8)(9)(10)NOTES: 1. Item from (2) through (10) are initialized to “0” after RAM clear.2. If

6-5EM18-33010A6. DIAG. TEST OPERATION(Revision Date: Dec. 10 ‘99)6.2 SELF TEST MODE2) Parameters#(11)(12)(13)(14)(19)(15)(20)(16)(21)(17)(22)(18)(23)(

6-6EM18-33010A6. DIAG. TEST OPERATIONNOTES: 1. If the automatic diagnosis printing results in an error, the printer will display the errormessage and

6-7EM18-33010A6. DIAG. TEST OPERATION Sample Print[Print Condition]• Preset count : 1• Print speed : 127 mm/sec.• Sensor : No sensor• Printing method

6-8EM18-33010A6. DIAG. TEST OPERATIONEEPROM OKEEPROM: Backup memoryRead/write checkOK: Data in the check area can be properly read/written.

6-9EM18-33010A6. DIAG. TEST OPERATIONSENSOR1Head up switch statusFixed to 1Cutter home position switch status0: Head opened1: Head closed0: H