Toshiba B-450-QQ Series User Manual

TEC Thermal PrinterB-450-QQ SERIESOwner’s ManualTable of Contents

4-14. DIP SWITCH FUNCTIONSEO1-330064. DIP SWITCH FUNCTIONSThe DIP switches are located at the rear of the printer.4. DIP SWITCH FUNCTIONSNOTES: 1. DIP

5-15. SET UP PROCEDUREEO1-330065. SET UP PROCEDURE5.1 REQUIREMENTS FOR OPERATIONThis machine has the following requirements:• The host computer must h

6-16. INSTALLATION PROCEDUREEO1-330066. INSTALLATION PROCEDURE6.1 INSTALLING THE SUPPLY HOLDER UNIT6.1 INSTALLING THE SUPPLY HOLDER UNITFig. 6-2Power

7-17. LOADING THE RIBBONEO1-330067. LOADING THE RIBBON7. LOADING THE RIBBONThe printer is capable of printing in both direct thermal and thermal trans

7-27. LOADING THE RIBBONEO1-330067. LOADING THE RIBBON5. Set the ribbon core (supply side) by fitting the protrusion into the notch.6. Turn the guide

8-1EO1-330068. LOADING THE PAPER8. LOADING THE PAPER8. LOADING THE PAPERThis supply holder accepts four sizes of label core: 38 mm, 40 mm, 42 mm and 7

8-2EO1-330068. LOADING THE PAPER8. LOADING THE PAPER3. Put the paper roll and supply holders on the supply holder unit.NOTE: Paper may be wound outsid

8-3EO1-330068. LOADING THE PAPER8. LOADING THE PAPERFig. 8-8Top CoverNOTE: Pass the paper straight from the supply holder to paper outlet. Failure to

8-4EO1-330068. LOADING THE PAPER8. LOADING THE PAPERStrip type:1 Strip the labels from the backing paper for about 200-mm long from the top edge of th

9-1EO1-330069. THRESHOLD SETTING9. THRESHOLD SETTINGFor the printer to maintain a constant print position it uses the transmissive sensor to measure

Copyright © 1999by TOSHIBA TEC CORPORATIONAll Rights Reserved570 Ohito, Ohito-cho, Tagata-gun, Shizuoka-ken, JAPANThis equipment has been tested and

10-1EO1-3300610. CARE/HANDLING OF THE PAPER AND RIBBON10. CARE/HANDLING OF THE PAPER AND RIBBON10. CARE/HANDLING OF THE PAPER AND RIBBON• Do not store

11-1EO1-3300611. GENERAL MAINTENANCE11. GENERAL MAINTENANCE11.1 CLEANINGTo help retain the high quality and performance of your printer it should be r

11-2EO1-3300611. GENERAL MAINTENANCE11.2 COVERS6. Clean the platen with a cloth moistened with alcohol.7. Remove any dust or glue from the detection a

11-3EO1-3300611. GENERAL MAINTENANCE11.3 REMOVING JAMMED PAPER11.3 REMOVING JAMMED PAPER1. Turn the power off.2. Open the top cover.3. Move the head

11-4EO1-3300611. GENERAL MAINTENANCE11.3 REMOVING JAMMED PAPER2. Fit the enclosed Allen Key into the right side of the cutter unit to rotate the cutt

12-1EO1-3300612. TROUBLESHOOTING12. TROUBLESHOOTING12. TROUBLESHOOTINGSolution1. Reload the paper correctly.→ Press the [PAUSE] key.2. Remove the caus

12-2EO1-3300612. TROUBLESHOOTING12. TROUBLESHOOTINGSolutionRemove the jammed paper and feedthe undamaged media through thecutter (See page 11-3).→ Pre

13-1EO1-33006APPENDIXAPPENDIXAPPENDIX ASCII Code Chart Font Sample Barcode Sample

14-1EO1-33006INDEXINDEXINDEXAAC Power inlet... 3-1Auto media feed ... 4-1BBar c

(i)Safety SummaryEO1-33006 Continued use of the machines in anabnormal condition such as when themachines are producing smoke orstrange smells may c

PRINTED IN JAPANEO1-33006E

(ii)Safety SummaryEO1-33006CAUTIONThis indicates that there is the risk of personal Injury or damage toobjects if the machines are improperly handled

TABLE OF CONTENTS1. INTRODUCTION ... 1- 11.1 APPLICABLE M

1-11. INTRODUCTIONEO1-330061.1 APPLICABLE MODEL1. INTRODUCTIONThank you for choosing the TEC B-450 Series thermal/transfer printer. This new generati

2-12. SPECIFICATIONSEO1-33006Supply voltage 100 ~ 120V, 60HzPower consumption 0.94 A, 47 W maximum (standby: 0.3 A, 18 W maximum)Operating temperatur

2-22. SPECIFICATIONSEO1-330062.3 PAPER (LABEL/TAG) SPECIFICATIONS2.3 PAPER (LABEL/TAG) SPECIFICATIONSNOTES: 1. To ensure good print quality and maximu

3-13. APPEARANCEEO1-330063. APPEARANCE3.1 FRONT/REAR VIEW3.1 FRONT/REAR VIEWFront View Rear View3.2 OPERATION PANELPOWER LED (Green)Lights when the po