Toshiba Tosvert VF-MB1/S15 User Manual

E6581738 TOSVERT VF-MB1/S15 PROFIBUS-DP Option Function Manual PDP003Z NOTICE 1. Read this manual be

E6581738 - 8 - 2.3. VF-MB1/S15 Communication parameters In a network, VF-MB1/S15 (PDP003Z) serves as a PROFIBUS slave device. PDP003Z configuratio

E6581738 - 9 - 3. Profile 3.1. Telegram Telegram of PDP003Z is set up by the configurator. The figures below show the Telegrams and configuratio

E6581738 - 10 - 3.2. STW Control Word Data PDP003Z supports only speed control mode. Bit Value Name Note 1 ON “Switched on” condition 0 0 OFF No

E6581738 - 11 - 3.3. ZSW Status Word Data Bit Valure Name Note 1 Ready To Switch-on Power supply is switched on 0 0 Not Ready To Switch-on -

E6581738 - 12 - 3.3.1. Tolerance Range (ZSW Bit 8) If the setpoint is changed: 1. ZSW Bit 8 is set 0 2. Calculate the tolerance. 3. Start the time

E6581738 - 13 - 3.4. State Machine STW: Control Word ZSW: Status Word : State : Condition Notes S

E6581738 - 14 - 3.4.1. Examples of driving by the State Machine When using the PROFIdrive profile, the frequency reference is set to HSW. The sett

E6581738 - 15 - 3.5. Access to the PROFIBUS parameter In the cyclic PROFIBUS-DP communication, the parameter data is transferred via Telegram 100,

E6581738 - 16 - 3.6. PROFIBUS parameter (PNU) PNU R/W data type Note 915 R Array [6] Unsigned16 PNU 915, IND 0 = the drive parameter c001 PNU

E6581738 - 17 - 3.6.1. Examples of reading the PROFIdrive parameter 3.6.1.1. Example 1. Reading the PNU 922 (Telegram) AK = 1 (Request paramete

E6581738 Contents 1. Introduction ...

E6581738 - 18 - 3.7. Access to VF-MB1/S15 parameter When access to VF-MB1/S15 parameter, set “1” to the PNU. The communication number of the drive

E6581738 - 19 - 3.7.1.3. Example 3. Reading the status monitor parameter (fe02 (The operation frequency)) AK = 6 (Request parameter value (array)

E6581738 - 20 - 4. Vendor Spec. Profile Cyclic command transmission (the value of the parameter c001 - c006) and monitoring (the value of the para

E6581738 - 21 - 4.1. How to use The purposes are adjustment by real time command transmission, and the monitor of an operation state by using cycl

E6581738 - 22 - 4.2. The overview of the VF-MB1/S15 parameter Refer to a communication functional description (E6581726/E6581913) for details. 4

E6581738 - 23 - 4.2.2. fa23 (Communication command 2) bit Function 0 1 Note 0 (Reserved) - - - 1 Electric power quantity reset OFF Reset El

E6581738 - 24 - 4.2.3. fa07 (frequency reference from internal option) Frequency reference is set up by 0.01Hz unit and the hexadecimal number. F

E6581738 - 25 - 4.2.6. fd01 (Inverter operating status 1 (real time)) bit Function 0 1 Note 0 Failure FL No output Under in progress - 1 Fai

E6581738 - 26 - 4.2.8. fd03 (Output current (real time)) The output current is read into 0.01% of units and by the hexadecimal number. For exam

E6581738 - 27 - 4.2.12. fc91 (Alarm code) bit Function 0 1 Remarks (Code displayed on the panel) 0 Over-current alarm Normal Alarming c flickin

E6581738 - 1 - 1. Introduction Thank you for purchasing the PROFIBUS-DP option “PDP003Z” for the VF-MB1/S15. Before using the PROFIBUS-DP option,

E6581738 - 28 - 4.2.14. fd07 (Output TB Status) bit TB Name Function (Parameter) 0 1 0 RY-RC Output terminal function selection 1A (f130) O

E6581738 - 29 - 5. Diagnostic When the communication loss occurs, PDP003Z returns the diagnosis telegram including the following information. B

E6581738 - 30 - 6. DP-V1 function DP-V1 acyclic communication is mainly used to read/write the parameter. VF-MB1/S15 parameter and the PROFIBUS pa

E6581738 - 31 - 6.1. Example1. Read the PROFIdrive parameter 6.1.1. Write Request data table (Read PNU 964 (0x03C4) IND 4) Field Description Va

E6581738 - 32 - 6.2. Example 2. Change the PROFIdrive parameter 6.2.1. Write Request data table (Change, set 0 to PNU 927 (0x039F)) Field Descr

E6581738 - 33 - 6.3. Example 3. Read the VF-MB1/S15 parameter When access to VF-MB1/S15 parameter, set “1000” to the PNU. 6.3.1. Write Request d

E6581738 - 34 - 6.4. Example 4. Change the VF-MB1/S15 parameter When access to VF-MB1/S15 parameter, set “1000” to the PNU. * This procedure chang

E6581738 - 35 - 7. PROFIBUS Local/Remote Operation The example below shows how to configure the VF-MB1 for local/remote operation. <Terminal f

E6581738 - 36 - 9. Appendix Function number 0x5E: Read Request 0x5F: Write Request 0x5E: Positive response for Read request 0x5F: Positive respon

E6581738 - 2 - Safety precautions On the drive and in its instruction manual, important information is contained for preventing injuries to users a

E6581738 - 3 - General Operation Warning Disassembly prohibited ▼ Never disassemble, modify or repair. Doing so could result in electr

E6581738 - 4 - Wiring Warning Mandatory ▼ Shut off power when installing and wiring this option. Wait at least 15 minutes and check to

E6581738 - 5 - Notes on use Notes ▼ Do not install the drive where the temperature or the humidity will change rapidly. ▼ Keep a distance of

E6581738 - 6 - 2. Connection Information This option allows the VF-MB1/S15 drive to be communicated with the cyclic command transmission and monit

E6581738 - 7 - 2.2. Status indicator The PDP003Z has two LEDs, ST (status) and DX (data exchange) to indicate the statuses of PROFIBUS-DP and the