OWNER,S MANUALSX-2801The FIRST thing to do after unpacking your newcordless telephone is:CHARGE THE BATTERY !Please read and follow the few instructi
10INSTALLATIONSETTING UP THE BASE UNIT (DESK TOP MOUNTING)For setting up the base unit follow the instructions below. • Plug the AC adaptor firmly int
11PreparationSETTING UP THE BASE UNIT (WALL MOUNTING)MOUNTING ON A STANDARD WALL PLATE:• Route the cords through the guides.• Place the base unit on t
12PreparationCHARGING THE BATTERY PACKIt is important to charge the battery for 12-16 hours continuouslywithout any interruption before you use the ha
13PreparationINSTALLATIONNOTES:• Use only the supplied battery pack (TRB-8000 power source 600mAh, 3.6VDC)• The battery pack is not charged properly i
14INSTALLATIONPreparationBefore using the Handset, make sure to read the following instructions.SETTING THE DIAL MODEDepending on your dialing system,
INSTALLATION15SETTING OR CANCELING THE AUTO TALK FUNCTIONIf the handset is placed on the base unit, you can answer a call bylifting the handset from t
16INSTALLATIONSETTING THE AREA CODEIt is necessary to program your area code so that local calls will bedisplayed properly on caller ID.1 Press . 2 P
INSTALLATION17USING A HEADSETYou can use an optional headset (part#: RC 008260) that has a 3/32-inch(2.5mm) plug.To connect the headset, open therubbe
18BASIC OPERATIONBasicsMAKING A CALLRECEIVING A CALLDELETETALKVOL/RINGREDIALFLASHTo hang up: Press , or return the handset to the base (Auto Standby)
BASIC OPERATION19Basics3 NUMBER REDIALYou can redial any of the last three numbers dialed from the handset:1 Press in standby mode. The last dialed n
2GETTING STARTED: DO THIS FIRST!FIRST, CHARGE THE HANDSET BATTERY!• Set your new phone in an out-of-the-way place near apower outlet where it will not
20BASIC OPERATIONBasicsTONE/PAUSEEXAMPLE : To make a call “0 12345678” with tone dialing inpulse mode, press .INTERFERENCE OR STATICIf you hear noise
BASIC OPERATION21PAGING THE HANDSET1 To locate the handset while it is off the base,press . The handset beeps for 60seconds.To stop paging, press or
22BasicsMEMORY DIALINGYou can store up to 20 telephone numbers and their associatednames in the memory.NOTES:• Always press a button within 20 seconds
MEMORY DIALING233 Press . 4 To enter a name, use the number keys.• See the steps for storing names and special characters. (see page 24)• If a name i
24MEMORY DIALINGBasicsFor example, to enter “Ted Doe” and 1 - 1 2 3 - 4 5 6 - 7 8 9 01 Pick up the handset and press and hold .2 Enter a number or
MEMORY DIALING25Basics10 When finished, press .11 Press to bestored.12 Press .IF YOU MAKE A MISTAKE WHILE ENTERING A NAMEUse or to move the cursor
26MEMORY DIALINGBasicsEDITING AND DELETING STORED NUMBERSYou can delete a number or simply store another one in its place.When you store a new phone n
MEMORY DIALING27Basicsb DELETING THE STORED DATA(1) Press or to move the pointer toselect or .(2) Press or .If is selected: A confirmation tonesoun
28CALLER ID/CALL WAITINGNOTES• Before you can take advantage of the Caller ID and Call Waiting features, youmust subscribe to these services from your
29Caller ID/Call waitingCALLER ID/CALL WAITINGSEARCHING CALLER ID MEMORYTo review who has called, follow the steps below.The caller ID memory retains
INTRODUCTION3• 900 MHz Digital Spread SpectrumTransmission with Extended TalkRange• 20 Channel Auto Scanning• 50 Name & Number Caller ID• Caller I
30Caller ID/Call waitingCALLER ID/CALL WAITINGEDITING CALLER ID DATAYou can edit the Caller ID data.1 Pick up the handset and press . Then, press or
31Caller ID/Call waitingCALLER ID/CALL WAITING4 Press . A confirmation tone sounds and the Caller ID datais stored. Press to return to standby.If yo
32Caller ID/Call waitingCALLER ID/CALL WAITINGDELETE ALL CALLER ID DATA:1 Press . 2 Press .Press or to select Yes or No.3 Press or .If you select ,
CALLER ID/CALL WAITING33CALL WAITING OPTIONSYour phone gives you new options for call waiting. At the touch of abutton, you can ask the caller to hold
34CALLER ID/CALL WAITINGThe options you can choose are shown below:Caller ID/Call waitingNo. Option Meaning1 Ask to Hold Prerecorded message asks 2nd
35Should any problem occur with the unit, use the following simple tests to determinewhether or not servicing is required.Additional InformationSOLUTI
36TROUBLESHOOTINGAdditional InformationPROBLEM SOLUTION•The handset is located away from the base or the battery has beendischarged. → Return the hand
TROUBLESHOOTING37When the handset isreturned to the base unitwith the volume level set atHigh, a momentary squealor howling sound maysometimes be hear
38WARRANTY/SERVICEAdditional InformationSERVICE REQUIREMENTSIf the cordless telephone should malfunction, or need changes or modifications, allrepairs
WARRANTY/SERVICE39TELEPHONE/TELEPHONE ANSWER MACHINE LIMITED WARRANTYToshiba America Consumer Products.Inc (“TACP”) and Toshiba Hawaii, Inc.(“THI”) ma
TABLE OF CONTENTS4PreparationINTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Features . . . . . . .
For technical assistance, purchase of accessoriesor service, please access www.toshiba.com/tacp.UCZZ01719BZ RC009798 Printed in ChinaIMPORTANTWe
TABLE OF CONTENTS5Steps for entering names and special characters . . . . . . . . . . . . . . .24If you make a mistake while entering a name . . . .
6PreparationIMPORTANT SAFETY INSTRUCTIONSWhen using your telephone equipment,basic safety precautions should alwaysbe followed to reduce the risk of f
7PreparationThe RBRCTMSealThe RBRCTMSeal on the (easily removable) nickel-cadmium battery(contained in our product) indicates that Toshiba America Con
8PreparationREDIALFLASHVOL/RINGL.D.TONEMEMPAUSEFUNCTIONDELETECHANNELLOCALSELECTTALKCIDLiquid Crystal Display (LCD)( ) button(Left arrow button) (page
LOCATION OF CONTROLS9PreparationCharging contactsBASE UNITDC IN 9V jack (page 10)LINE modular jack (page 10)CradleAntennaIN USE/CHARGE LEDbutton (page
Comments to this Manuals