Toshiba IK-SX1L User Manual

1For Customer UseEnter below the Serial No.which is located on thebottom of the cabinet. Re-tain this information for fu-ture reference.Model No.: IK-

106.4 Electric shutter speed switchThis sets the electric shutter speed and the exposure time for the 1-pulse trigger.Electric shutter speed1/151/1001

117. Operation mode7.1 Internal synchronizationHorizontal synchronization: 15.998 kHz (28.63636 MHz x 1790 clocks)Vertical synchronization: 15 fps (14

127.3 Internal synchronization partial readoutWhen the partial scanning is set, the frame rate can be increased by decreasing the num-ber of output li

137.4 1-pulse triggerExposure starts by the trigger signal input to the DIGITAL terminal, and outputs a 1-frameimage. The shutter speed (exposure peri

147.6 Pulse width triggerThis is the mode to set the exposure period by the pulse width of the trigger signal ap-plied to the DIGITAL terminal. This a

158. Partial ScanningThe set number of vertical lines is partially scanning, and the frame rate can be increased.8.1Scanning area 1/15(70 lines, 60 fp

169. Timing Chart9-1 All pixel scanning1 V-rateInternal synchronization1-pulse trigger, pulse width trigger1068HVDFENVideo output1040H11H9H8HVideo per

172 H-rate1790HDLEN13924021804The digits indicate the number of clocks.1 clock = 34.9 ns (28.63636 MHz)Video outputVideo period9.2 Draft mode1 V-rate2

182 H-rate9.3 Partial scanning1 V-rateInternal synchronization1790HDLENVideo output40213924180Video periodThe digits indicate the number of clocks.1 c

191-pulse trigger, pulse width trigger2 H-rateFEN99H66H50H36H9H3H70H400H560H700H98H65H49H35H276H540H668H780HVD(internal synchronization output positio

2Safety precautionsRead the following safety precautions carefully before using the product. These instructionscontain valuable information on safe an

2011. SPECIFICATIONS10. TROUBLESHOOTING CHARTSymptomsNo imagePossible causes• Is power properly supplied?• Is the lens iris adjusted properly?• Is the

2112. EXTERIOR VIEWDC IN 12VMODE SELECTDIGITALGAINDC IN 12VMODE SELECTDIGITALGAIN3-M3 (screw depth 4mm[0.16"])IK-SX1LIK-SX144 [1.73"]22 [0.8

22Memo

23Memo

24LIMITED WARRANTYCCD CAMERAThe Imaging Systems Division of Toshiba America Information Systems, Inc. (“ISD”) makes the following limited warran-ties

3Caution• Keep the followings when installing.• Do not put the product on a Inflammable material such as carpet or blanket.• Do not put the product in

4TABLE OF CONTENTS1. CAUTIONS ON USE AND INSTALLATION... 52. COMPONENTS ...

51. CAUTIONS ON USE AND INSTALLATION• Carefully handle the units.Do not drop, or give a strong shock orvibration to the camera. This may causeproblems

611111Picture-shooting areaThe protection cap is attached on the lens mount portion. After removing the cap, mountthe lens. Be careful not to scratch

74. CONNECTIONS4.1. Standard ConnectionLensIK-SX1LIK-SX1Image processorDC IN 12VDC power supplyCamera cable(option)4.2. Cautions on Connection• When c

81234567891011121314+D0 (Video Data (LSB))+D1 (Video Data)+D2 (Video Data)+D3 (Video Data)+D4 (Video Data)+D5 (Video Data)+D6 (Video Data)+D7 (Video D

96. SettingMODE SELECT switch6.1 Gain switchUse this switch when the image is dark even if the lens iris is fully opened. When the gainON is set, adju