For Customer UseEnter below the Serial #which is located on thebottom of the cabinet. Retainthis information for future ref-erence.Model # IK-HR1S
10㽲 Refer to the item "4. CONNECTION", and connect the equipment correctly.㽳 Turn on the connected equipment and the camera. 㽴 Aim the le
11MeaningDisplayAWB OK Automatic white balance adjustment finished correctly. AWB NG LEVEL LOW Automatic white balance adjustment cannot be performed
12(1) MANUAL(Manual gain) Gain adjustment is performed on the GAIN menu. The adjustment range is from 0 to 18dB in 1dB steps. (Refer to the item “7.3
13Available selectionsItemPreset value (Factory setting) MANUALAUTO, MANUAL, SSMODEOFF *2 OFF *1 MANUAL, OFFMODE1123/1125H748/750HAWBAWB, ATW, MANUALM
14Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized in the scen
15䊶 Select the menu to change the setting by referring to the item “7.1 Using the Menus”.䊶 When the [MENU UP], [MENU DOWN] buttons are pressed, the “㸢
16(b) Changing the automatic shutter detection (ratio between peak and average value)㽲 Move the “㸢” to PEAK/AVE by pressing [MENU UP], [MENU DOWN] bu
17䋨䋨䋨䋨1䋮䋮䋮䋮2䋩䋩䋩䋩 Changing the setting in MANUAL mode Shutter mode AUTO, MANUAL, SS -- 1 SHUTTER -- <FILE A> Shutter speed setting
182 GAIN (Video gain)GAIN has two modes; MANUAL, OFF. Move the “ ” to MODE, press the [DATA UP], [DATA DOWN], and select one of the two modes : MA
19(c) Changing color temperature setting㽲 Move the “㸢” to C.TEMP by pressing [MENU UP], [MENU DOWN] buttons. 㽳 Select either 3200K or 5600K by press
2SAFETY PRECAUTIONSSafety iconsThis manual contains safety instructions that must be observed in order to avoid potentialhazards that could result in
20䋨䋨䋨䋨3䋮䋮䋮䋮2䋩䋩䋩䋩 Changing the setting in ATW(Automatic Tracking White balance) mode White balance mode AWB, ATW, MANUAL -- 3 WHT BAL --
21䋨䋨䋨䋨3䋮䋮䋮䋮3䋩䋩䋩䋩 Changing gain in MANUAL mode White balance mode AWB, ATW, MANUAL Red gain adjustment -100 to 100 -- 3 WHT BAL -- <FILE A
22䋨䋨䋨䋨4䋩䋩䋩䋩 PROCESSGamma correction ON, OFF Gamma correction level setting -10 to 10 -- 4 PROCESS -- <FILE A> GAMMA ON/OFFGAMMADe
23䋨䋨䋨䋨4䋮䋮䋮䋮3䋩䋩䋩䋩 Changing detail (outline) gain 㽲 Move the “㸢” to DTL GAIN by pressing [MENU UP], [MENU DOWN] buttons. 㽳 Select the desired value of
24䋨䋨䋨䋨5䋩䋩䋩䋩 MATRIX(Matrix color correction)Matrix color correction ON, OFF Red hue setting -- 5 MATRIX -- <FILE A>Yellow hue
25䋨䋨䋨䋨6䋩䋩䋩䋩 OPTION -- 6 OPTION -- <FILE A> RS-232C baud rate 9600bps, 19200bps BAUD RATE9600bps䋨䋨䋨䋨6䋮䋮䋮䋮1䋩䋩䋩䋩 Changing RS-232C ba
26Items to be checkedSymptomNo picture 䍃 Is power supplied correctly? 䍃 Is the lens iris adjusted correctly? 䍃 Are the camera and video cables conn
27Unit : mm [inch] 10. EXTERNAL APPEARANCE DIAGRAM 4-M2 Depth 3 [0.118]4-M3 Depth 3 [0.118]44 [1.73]44 [1.73]26 [1.02]25 [0.98]5 [0.2]56 [2.2]25 [0.98
Limited Warranty – TOSHIBA CMOS Color CameraThe Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the foll
3DisclaimerWe disclaim any responsibility and shall be held harmless for any damages or losses incurred by theuser in any of the following cases:1. Fi
41 CAUTIONS ON USE AND INSTALLATION ... 2 COMPONENTS ...
58 BEFORE MAKING SERVICE CALL...9 SPECIFICATIONS...
61 Camera ... 1 2 Accessories a Instru
718246759Optical areaHD-SDI terminalDISP buttonREMOTE terminal3FORMAT switchMounting holes M3Mounting holes M2PAGE button[ Rear ][ Front ][ Bottom ]ME
8IK-HR1SDC IN 12VLens (option) 75 ohms coaxialcable (option)HD-SDI inputHD-SDI (BNC connector)HD- capable monitor (option)DC power supply(option)AC ad
94. 3A Connector Pin AssignmentsDC IN 12V terminal1 +12V2 +12V3GND4GNDREMOTE terminal123TXDRXDGNDRear panel view4 3 Connection on Rear Panel 㪩㪜㪤
Comments to this Manuals