For Customer UseEnter below the Serial #which is located on thebottom of the cabinet. Retainthis information for future ref-erence.Model # IK-HD1C
10DC IN 12V1 +12V 2 +12V 3 GND 4 GND REMOTE1234 5 6 7 8 9 NC NCNCNCGND NCRXD TXD NC5 3A Connector Pin Assignments䊶 Only use optional camera head mod
11㽲 Refer to the item “5. CONNECTION”, connect the equipment correctly. A camera head "IK-HD1H" needs to be connected to this camera contro
12ATW Automatic TrackingWhite Balance䋩䋩䋩䋩AWB 䋨䋨䋨䋨䋨䋨䋨䋨Automatic White Balance䋩䋩䋩䋩MANUAL 䋨䋨䋨䋨Manual White Balance䋩䋩䋩䋩Outline The camera measures the obj
13MeaningDisplayAWB OK Automatic white balance adjustment finished correctly. AWB NG LEVEL LOW Automatic white balance adjustment cannot be performed
14Five scene files (A, B, C, D, E) are available as user memories for this unit. These are chosen dependingon shooting conditions. By using the [FILE]
15Due to the lens used or the environmental condition, color shading may occur at the upper and lower edgeof the screen. If this happens, the shading
16Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The contents once set are memorized in the scen
17䊶 Select the menu to change the setting by referring to the item “7.1 Using the Menus”.䊶 When the [MENU UP], [MENU DOWN] buttons are pushed, the “㸢”
18䋨䋨䋨䋨1䋮䋮䋮䋮1䋩䋩䋩䋩 Changing the setting in AUTO mode Shutter mode AUTO, MANUAL, SSVideo level adjustment -100 to 100 Peak and average ratio adjus
19(d) Changing the automatic shutter zone area The available picture area is shown by the shading correction on the screen that is parted in 64.㽲 Move
2SAFETY PRECAUTIONSSafety iconsThis manual contains safety instructions that must be observed in order to avoid potentialhazards that could result in
20䋨䋨䋨䋨1䋮䋮䋮䋮2䋩䋩䋩䋩 Changing the setting in MANUAL mode Shutter mode AUTO, MANUAL, SS -- 1 SHUTTER -- <FILE A> Shutter speed setting
212 GAIN (Video gain)GAIN has three modes; AUTO, MANUAL, OFF. Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select one of the three m
22䋨䋨䋨䋨3䋩䋩䋩䋩 WHT BAL(White Balance)The WHT BAL has three modes; AWB, ATW, MANUAL. Move the “ ” to MODE, push the [DATA UP], [DATA DOWN], and select
23䋨䋨䋨䋨3䋮䋮䋮䋮2䋩䋩䋩䋩 Changing the setting in ATW(Automatic Tracking White balance) mode White balance mode AWB, ATW, MANUAL -- 3 WHT BAL --
24䋨䋨䋨䋨3䋮䋮䋮䋮3䋩䋩䋩䋩 Changing gain in MANUAL mode White balance mode AWB, ATW, MANUAL Red gain adjustment -100 to 100 -- 3 WHT BAL -- <FILE A
25䋨䋨䋨䋨4䋩䋩䋩䋩 PROCESSGamma correction ON, OFF Gamma correction level setting -10 to 10 -- 4 PROCESS -- <FILE A> GAMMA ON/OFF ON
26䋨䋨䋨䋨4䋮䋮䋮䋮3䋩䋩䋩䋩 Changing detail (outline) gain 㽲 Move the “㸢” to DTL GAIN by pushing [MENU UP], [MENU DOWN] buttons. 㽳 Select the desired value of
27䋨䋨䋨䋨5䋩䋩䋩䋩 MATRIX(Matrix color correction)Matrix color correction ON, OFF Red hue setting -- 5 MATRIX -- <FILE A>Yellow hue
28䋨䋨䋨䋨6䋩䋩䋩䋩 SYNCWhen an external sync signal is input, the display changes from INT (internal sync) to EXT.(external sync) automatically. INT E
29䋨䋨䋨䋨7䋩䋩䋩䋩 OPTIONOUTPUT Y/Pb/Pr, RGBSHADING MODE SET, MANUAL, OFF -- 7 OPTION -- <FILE A> RS232C baud rate 9600bps, 19200b
3DisclaimerWe disclaim any responsibility and shall be held harmless for any damages or losses incurred by theThe following description is for that a
30䋨䋨䋨䋨7䋮䋮䋮䋮5䋩䋩䋩䋩 Changing RS232C baud rate 䋨䋨䋨䋨7䋮䋮䋮䋮6䋩䋩䋩䋩 Changing OSD OUTPUT mode㽲 Move the “㸢” to BAUD RATE by pushing [MENU UP], [MENU DOWN] butto
31When using the unit with an external sync signal to EXT. SYNC terminal on the rear panel. When the external sync signal is input, the camera automat
32Items to be checkedSymptomNo picture 䍃 Is power supplied correctly? 䍃 Is the lens iris adjusted correctly? 䍃 Is the power switch on, and the powe
33Power supply 12V DC㫧10%Power consumption Approx. 10.3 W (including a camera head) Pick-up system RGB, 3CCD, Micro prism system Image sensor 1/3 inch
34Unit : mm [inch] 10. EXTERNAL APPEARANCE DIAGRAM 㪋㪋㪅㪍㩷㪲㪈㪅㪎㪍㪴㪋㪇㩷㪲㪈㪅㪌㪏㪴㪈㪏㪍㩷㪲㪎㪅㪊㪉㪴㪈㪈㪇㩷㪲㪋㪅㪊㪊㪴㪈㪏㪅㪏㪊㪲㪇㪅㪎㪋㪴㪍㪉㫧㪇㪅㪈㩷㪲㪉㪅㪋㪋㫧㪇㪅㪇㪇㪋㪴㪋㪄㪤㪊㩷㪙㪛㪉㪎㩷㪲㪈㪅㪇㪍㪴㪈㪊㪐㫧㪇㪅㪈㪌㩷㪲㪌㪅㪋
Limited Warranty – TOSHIBA CCD CameraThe Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes the following l
41 CAUTIONS ON USE AND INSTALLATION ... 2 COMPONENTS ...
5 (2) External sync frequency range ... (3) Using the unit wit
61 Camera Control Unit ... 1 2 Accessories a Instruction m
7Available selectionsItemPreset value (Factory setting) MANUALAUTO, MANUAL, SSMODEOFFOFFAUTO, MANUAL, OFFMODEOFFAWBAWB, ATW, MANUALMODEAUTO level -100
83421123 458796Camera cablefor “IK-HD1H”terminalPOWER switchPOWER LEDFILE buttonGAIN buttonDISP buttonPAGE buttonMENU UP(SHD) buttonMENU DOWN(SHD) but
9㽽 DC IN 12V terminal Accept a DC power input (12V). 㽾 Y/G terminal Outputs Y or G. (BNC connector)㽿 PB/B terminal Outputs PB or B. (BNC connector)㾀 P
Comments to this Manuals